Car Painting Tape Rewinding Machine

Car Painting Tape Rewinding Machine

Rewinding Machine common fault - Longitudinal cutter swing
1. Round knife bearing wear - Replace the bearing.
2. Tool holder sliding bearing wear - Replace the bearing.
3. Lock the cylinder leak - replace or repair the cylinder.

Car Painting Tape Rewinding Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

3. Double curved roller section:
Mainly composed of bracket, double arc roller, worm gear adjustment device, angle gear, air motor and other devices
        After cutting the paper, it enters a set of curved roller stretching assembly, which is mainly composed of two curved rollers and an adjusting mechanism. The adjusting mechanism is driven by a pneumatic motor, and through a set of angular gear mechanism and two sets of worm gear reduction mechanisms, according to The wrap angle between the web and the curved roller needs to be adjusted at any time. The curved roller is introduced from abroad to ensure its performance. This system effectively stretches the web, eliminates wrinkles, and separates the paper rolls.
4. Automatic paper feeding department:
The guiding paper-feeding roller and the compressed air and the guiding plate are adopted, so that the paper head can smoothly and quickly and accurately complete the paper-feeding action on the uniform air cushion generated by the guiding plate and the compressed air, and between the two bottom rollers is used between the conveyor belt and the bottom roller. Friction drive, so that the paper head is close to the surface of the bottom roller, and the paper-feeding action is completed under the action of compressed air.

Car Painting Tape Rewinding Machine

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad
Rewinding machine is an important papermaking machine. It is usually installed behind the paper machine. Its speed should be 2-3 times of the speed of the paper machine, generally 1500-1800m/min, up to 300om/min. When threading, run at a maximum speed of 1:100. In order to ensure continuous paper and loose paper during the rewinding process, the tension of the paper web must be kept constant; in order to ensure the tight and loose quality inside the finished paper, the load distribution of the front and rear bottom roller motors must be performed. Therefore, the main performance requirements of the rewinder for the electric drive system are long-term linear speed, adjustable speed and wide speed range, and fast response.
The control of the early rewinder is mainly based on DC drive, and the DC control system is composed of discrete components or analog regulators to realize the above control functions. Since the transmission of analog signals requires a one-to-one physical connection, the signal changes slowly, which increases the overhead of computer speed and accuracy, and the anti-interference ability of signal transmission is poor, and paper breakage and wrinkling often occur in the production process. So in the mid-to-late 1980s, the analog regulator was replaced by a digital regulator, and the DC digital control system of the winder appeared. This control system is more stable, reliable and suitable for maintenance than the analog system, and is more suitable for interface with the factory computer. In the mid-1990s, most of the newly-invested rewinders in the domestic paper industry used all-digital DC-speed converters produced abroad, and the more famous ones were the 6RA7O series from Siemens and the 590 series DC-speed converters from Continental Transmission.
Due to the DC motor commutator and the brush, under the stable conditions, the design speed of the winder can only reach 1800m/mni, and the accuracy of the digital regulator is still limited to about 0.08% of the maximum speed, which can not meet the high speed paper. The matching requirements of the machine (the speed of the winder should be 2-3 times the speed of the paper machine). In the early 1980s, European and Japanese developed AC variable frequency speed control devices. This technology was successfully introduced to the United States in the mid-1980s and used in rewinders. The biggest advantage of the AC drive is that the AC motor is simple in construction and reliable in operation, and it requires much less maintenance and repair than DC motors.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com