Tape Large Rewinder

Tape Large Rewinder

Rewinding Machine common fault - Longitudinal cutter swing
1. Round knife bearing wear - Replace the bearing.
2. Tool holder sliding bearing wear - Replace the bearing.
3. Lock the cylinder leak - replace or repair the cylinder.

Tape Large Rewinder

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

Tape Large Rewinder

Belt rewinding machine design and working principle ---

1 belt roller device
Structure
The belt and stick set consists of two belt rollers with intermediate and end supports! A rubber support belt surrounds the belt roller. The inner surface of the support belt has a guiding profile that controls the operation of the belt. There is also a correspondingly concave surface on the belt roller. The belt roller has been joined together by a rocker and a hydraulic cylinder from below. The belt tension can be adjusted with a hydraulic cylinder during the winding process.
The motor drives the rear belt roller to run, and the other roller is carried by the belt. The belt roller is equipped with a hydraulic brake system. The belt roller bearing housing is lubricated with lubricating oil. The oil flow and temperature of the lubricating oil system are detected by the sensor. There is a directional blow tube between the two rolls to ensure that no space remains in the space between the two rolls. The lifting device has been installed under the belt. The lifting device is used for changing rolls. The lifting device comprises a hydraulic cylinder and a lifting plate interlocked with the rear bottom roller during the lifting process.
Belt roller unit:
1- bottom roller
2- rear belt roller
3- front belt roller
4- belt
5-belt telescopic hydraulic cylinder

Principle of operation
The core is placed between the back bottom roll and the back belt roll. The paper core is supported at that position throughout the initial crimping process up to a diameter of approximately 500 mm (17.9 in). The over 500 mm (17.9 in) belt begins to support the increasing area of ??the paper roll, and the weight of the roll is reached when the paper roll is particularly large. Mainly supported by a belt.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com