Plastic Adhesive Bopp Tape Rewinding Machine

Plastic Adhesive Bopp Tape Rewinding Machine

Rewinding Machine common fault - The coil is not tight during operation
1. Unwinding tension controller is not open - Open unwinding tension controller switch
2, did not press the reset button - press the reset button on the two tension controllers
3, the unwinding tension controller tension is too small - increase the unwinding tension controller output current
4, tension controller failure - contact the manufacturer

Plastic Adhesive Bopp Tape Rewinding Machine

Rewinding Machine safety operation guide - 

Seventh, production operations and quality control during the rewinding process:

4, pay attention to the quality of the rewinding of the paper roll when rewinding, found zigzag, knife, running,
If the color difference is serious, skipping, chain printing, wrinkling, violent edge, etc., the result should be stopped in time. Only after the inspector confirms can the machine be re-rolled.
5. When the rewinding operation is running, the host must be at the console, and must not leave at will to prevent accidents. Transport
The speed of lifting and lowering is slow, and the speed of the vehicle cannot exceed the prescribed limit.
6. When loading the paper core tube, it is necessary to select the paper core with the same outer diameter and the length specification in line with the quality standard.
The installation of the cylinder requires a large deviation of the outer diameter and needs to be replaced.

Plastic Adhesive Bopp Tape Rewinding Machine

Rewinder mechanical structure and control process ---

 

I. Overview of the double-roller under the paper rewinding machine
The mechanical structure of the lower paper rewinding machine is shown in Figure 2-1. It can be seen from the mechanical structure diagram of the rewinding machine that the lower paper rewinding machine is fed into the paper web from below the rewinding machine. The paper web is wound around a support roll and then rolled up with a roll of paper. The paper is ejected from the unwinding roll, passed through the lower transfer roll, and then the web passes through the slitting mechanism at a fixed position, bypassing the front backup roll (press The second roller in the direction of the paper line or the back support roller is then wound on the take-up reel.
During the rewinding process, the paper web passes through the eject roller, and the tension force formed by the paper web pulls the paper roll toward the support roller, and the tension of the paper roll is stabilized by the action of the tension, and the rewinding machine can be made at a high speed roll. The quality of the paper roll can be guaranteed when taken. The lower thread rewinding machine can also control the pressure between the platen roller and the paper roll by changing the transmission torque difference of the two supporting rollers, so that the pressure of the finished paper roll can be controlled, and the quality of the paper roll can be Do a good job of control.
It can be seen from the figure that since the slitting mechanism of the lower threader rewinding machine is installed at a fixed position, this can avoid axial sway during the rewinding process, and also facilitates the control of the winding of the paper roll. The role of most of these rewinders in the Middle East is not very high, very close to the ground, the center of gravity, relatively low, due to the lower center of gravity, the rewinder can remain stable at high speeds, so this Types of rewinding machines are widely used, and most of the paper mills in China use the lower thread rewinding machine. Through many practices, this rewinding machine is also the best performance. And its speed can reach 2,500 meters per minute, the width is also long, can reach 10 meters, can handle the rewinding of different types of paper, from low basis to cardboard can be re-rolled. Of course, it also has its own shortcomings. The disadvantage is that because it is close to the ground, it is not easy for the operator to access the bottom of the machine. It is also difficult to guide the paper. Therefore, when the mechanical equipment is installed, a pit will be placed under the machine. In order to make the operator more accessible, the high-grade rewinding adopts the automatic threading structure, and there is no such problem.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com