Reflective Tape

Reflective Tape

Rewinding Machine common fault - The coil is not tight during operation
1. Unwinding tension controller is not open - Open unwinding tension controller switch
2, did not press the reset button - press the reset button on the two tension controllers
3, the unwinding tension controller tension is too small - increase the unwinding tension controller output current
4, tension controller failure - contact the manufacturer

Reflective Tape

Guolian Small Winder Introduction---

First, the function: a variety of tape defective products re-rolled
Second, the characteristics:
A. The take-up shaft is driven by a DC 1HP motor and can be steplessly changed.
B. Automatic counting, convenient for setting the length of the winding.
C. The rewinding tension is adjusted by the spring, and the tension adjustment is convenient.
D. The structure of the machine is light and compact, and it is a desktop device, which is convenient to move.

Third, the specifications
1. Roller surface width: 105mm
2. Maximum discharge diameter: standard is 150mm and length is 400mm
3. Take-up diameter: Ø76mm-300mm
4. Rewind width: 12mm-100mm lengthening type is 300mm
5. Take the paper heart: paper tube 3”
6. Mechanical speed: 0~150M/min per minute

Fourth, the host configuration
1. Discharge shaft: 3" movable type (1)
2. Dispensing rack: lengthened 300mm diameter (1)
3. Main motor: DC motor 1HP (1 set)
4. Take-up tension: Spring control (1 set)
5. Length control: four-digit electronic counter (1 group)
6. Take-up shaft: 3" tube core (1 group)

Reflective Tape

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com