Mounting Tape

Mounting Tape

Rewinding Machine common fault - The coil does not run or is broken
1. Winding tension controller is not open - Open winding tension controller switch
2, the speed of the governor is too low - increase the speed of the governor
3, did not press the reset button - press the reset button on the two tension controllers
4, the tension tension controller tension is too small - increase the winding tension controller output current
5, unwinding tension control tension is too large - reduce the unwinding tension controller output current
6, the running button is damaged - replace the run button
7, tension controller failure - contact the manufacturer
8, governor failure - contact the manufacturer

Mounting Tape

Rewinding Machine operation safety regulations - 

Second, the operation steps:

7. When the layers of paper are completely flat and enter the rewinding, the waste coils are taken out to the normal production state. 8, check the production situation:
(1) Check whether the two ends of the base paper are symmetrical. For example, the auger can adjust the auger on the unloading frame to the ends of the paper. (2) Check whether the punched paper is clear, the punching is not clear or the missing teeth are checked. Whether the knife is broken or not
Whether the wire is loose, adjust the height of the bottom knife, and mass production after inspection;
(3) Check whether the paper feeding tension of the rewinding paper is consistent, keep the paper surface flat and no wrinkles, such as inconsistency
Then adjust the paper return belt hand wheel on the paper exit frame;
(4) Check whether the paper between the embossing stick and the winding area is flat and tight, if it meets the requirements, if it does not meet the requirements,
Then adjust the gearbox handwheel (when adjusting the gearbox handwheel, you can't stop the adjustment, you need to turn it on slowly); (5) Check whether the semi-finished paper roll is tight, the diameter and weight meet the product standard requirements, and the two ends are neat (straight
The deviation of the diameter shall not exceed ±1mm, and the weight deviation shall be within ±2);
(6) Whether the width of the glue seal of the paper ball meets the standard (package standard is 10mm-15mm), the penetration of glue
No more than 3 single-layer papers;
(7) Do not arbitrarily tamper with the inverter, programmed wiring and settings in the electric box; (8) Non-operator operators must not let the machine operate without the consent of the supervisor;

Third,. After the above steps are checked normally, Slowly speed up to normal operation.

Mounting Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
      Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
      The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com