Rewinding Machine common fault - Rolls are not collected
1. The original coil is not uniform - Finish the original coil to ensure that the original coil is neat
2, paper core size head - check the paper core
3, only start a short period of time - normal phenomenon,
4, bearing damage - bearing damage is often accompanied by abnormal noise, pay attention to check the bearing, found that the damage is replaced in time
5, shaft damage - contact the manufacturer
Rewinding Machine operation safety regulations -
Second, the operation steps：
4, traction paper head, start switch paper, the paper passing through the following parts: curved rod - towel press paper knife in front of punching knife - punching knife - curved rod - felt paper stick - winding wheel (the whole process It is necessary to use jog feed or slow speed. When entering the punching knife, it is strictly prohibited to twist the paper into one or more layers, and pay attention to safety);
5. Set the number of production sections according to product specifications;
6. Take a bundle of paper tubes into the paper tube push-up rack of the machine, spread the paper tube, take one into the middle of the two winding wheels, (and then press the embossing stick), and slowly rotate the machine. Rewinding (the ropes bundled with paper tubes should be placed in accordance with the regulations, and should not be randomly placed);
Guolian High Speed ??Slitting Rewinder Technical Description ---
The specific technical structure is described as follows:
2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc