Grip Tape

Grip Tape

Rewinding Machine common fault - Rolls are not collected
1. The original coil is not uniform - Finish the original coil to ensure that the original coil is neat
2, paper core size head - check the paper core
3, only start a short period of time - normal phenomenon,
4, bearing damage - bearing damage is often accompanied by abnormal noise, pay attention to check the bearing, found that the damage is replaced in time
5, shaft damage - contact the manufacturer

Grip Tape

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

Grip Tape

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com