Pvc Warning Tape

Pvc Warning Tape

Rewinding Machine safety operation guide - 

Second, the rewinding machine is opened and shut down:
1. Check the equipment thoroughly before starting the machine to check whether the round knife and the bottom knife are in good condition.
2. Whether the size of the round knife meets the requirements of finished products and cutting specifications
3. Hang the rewinding paper roller on the paper feeding frame, and make the brake and roller contact with each other.
Whether the fuse cover on both sides of the core and the barrel of the core is covered.

Pvc Warning Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

Second, the system configuration
1. Main transmission part: 1 set of paper-removing brake generator, 400kW (YVP4501-6 or
1LA8357-6), one roller motor (YVP225S-4), 37kW, two pressure roller motors (YVP132S-4), 5.5kW, two coiling motors (YVP355L2-4) (one for each front and rear roller) , 315kW, 6 paper cutter motor, 0.55kW, total installed capacity 1082kw (model and power are subject to final design). The rectification feedback and the inverter unit and the tension controller matched with the above constitute a transmission control system.
2. Logic control part: PLC host 1 block.
3. The logic control system selects the S7-400 series products of SIEMENS.
4. Tension control part: 1 set of tension detection and control system, using Sweden
NOBEL products.
5. 1 set of coiling roller pressure detection and control system.
6. The diameter detecting sensor of the take-up roller.
7, with position detection, pressure detection, liquid level detection, safety detection sensor and phase
The control agency should be controlled.
8. On-site operation panel, logic control panel, and electric drive panel.

Pvc Warning Tape

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com