Rewinding Machine safety operation guide -
Third, the rewinding machine opening and closing operation sequence:
1. Start the rewinding machine and the paper edge blower motor to put the speed to the crawling speed. Tearing the web
Into one. The paper edge is wound into a roller according to the specified path, and the round paper web must be straightened. Loosen and tightly adjust, press the switch and the paper core tube to stick the tape. Stick the paper web to the paper core tube and start crawling. At the same time, the end of the paper roll is flat. The paper can not be wrinkled or discounted to ensure the quality of the rewinding. When the paper has broken ends, the joints are operated, the broken ends are connected and the joint quality is ensured.
Rewinding Machine operation safety regulations -
Second, the operation steps：
7. When the layers of paper are completely flat and enter the rewinding, the waste coils are taken out to the normal production state. 8, check the production situation:
(1) Check whether the two ends of the base paper are symmetrical. For example, the auger can adjust the auger on the unloading frame to the ends of the paper. (2) Check whether the punched paper is clear, the punching is not clear or the missing teeth are checked. Whether the knife is broken or not
Whether the wire is loose, adjust the height of the bottom knife, and mass production after inspection;
(3) Check whether the paper feeding tension of the rewinding paper is consistent, keep the paper surface flat and no wrinkles, such as inconsistency
Then adjust the paper return belt hand wheel on the paper exit frame;
(4) Check whether the paper between the embossing stick and the winding area is flat and tight, if it meets the requirements, if it does not meet the requirements,
Then adjust the gearbox handwheel (when adjusting the gearbox handwheel, you can't stop the adjustment, you need to turn it on slowly); (5) Check whether the semi-finished paper roll is tight, the diameter and weight meet the product standard requirements, and the two ends are neat (straight
The deviation of the diameter shall not exceed ±1mm, and the weight deviation shall be within ±2);
(6) Whether the width of the glue seal of the paper ball meets the standard (package standard is 10mm-15mm), the penetration of glue
No more than 3 single-layer papers;
(7) Do not arbitrarily tamper with the inverter, programmed wiring and settings in the electric box; (8) Non-operator operators must not let the machine operate without the consent of the supervisor;
Third,. After the above steps are checked normally, Slowly speed up to normal operation.
Rewinder mechanical structure and control process ---
As the last process in the papermaking industry, the winder is the fastest running machinery in papermaking machinery. Its speed can reach 1500~1800m/min or even the speed can reach 3000m/min or more. The winder is in the papermaking industry. The important role that can not be ignored, the paper roll from the paper machine must be rewinded by the winder to get the finished paper roll we need, and the quality of the finished paper roll is not only determined by the paper machine, The role of the winder is also of particular importance.
The working principle of the winder is to install the large paper roll produced from the paper machine on the paper exit frame of the winder. In order to maintain a certain tension of the paper web, the brake device must be installed on the paper return frame. A brake motor is installed on the paper exit frame. If the paper breaks during the rewinding process, the brake device can also brake quickly to reduce paper loss. The web is cut to the width we need by the slitting roller, the paper guide roller and the winder slitting mechanism, and then re-rolled into a paper roll according to the required tightness and the diameter of the finished paper roll. The main structural parameters of the winder are the width of the paper roll that can be rewinded, the maximum speed that the rewinding machine can reach, the quality of the finished paper roll, the maximum diameter of the ejecting roll and the roll paper, and the method of cutting the paper.
There are many types of rewinders, and other devices can be equipped in the rewinder as needed to become a joint machine. The rewinder can basically be divided into the following five types: upper paper rewinder, lower paper rewinder, single roll rewinder, special rewinder and thin paper rewinder. Since the research object of this subject is mainly for the lower threading rewinding machine, the introduction and explanation of the double bottom roller lowering paper rewinding machine will be given.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc