Led Tape Light

Led Tape Light

Rewinding Machine safety operation guide - 

Third, the rewinding machine opening and closing operation sequence:
1. Start the rewinding machine and the paper edge blower motor to put the speed to the crawling speed. Tearing the web
Into one. The paper edge is wound into a roller according to the specified path, and the round paper web must be straightened. Loosen and tightly adjust, press the switch and the paper core tube to stick the tape. Stick the paper web to the paper core tube and start crawling. At the same time, the end of the paper roll is flat. The paper can not be wrinkled or discounted to ensure the quality of the rewinding. When the paper has broken ends, the joints are operated, the broken ends are connected and the joint quality is ensured.

Led Tape Light

Four release and one rewinding machine operation program ---

6. Check if the power indicator on the outside of the tension control cabinet is lit.
7. In the touch screen, you need to input or rewrite the following parameters:
1 counting length is cleared (if it is necessary to re-measure the length);
2 automatic acceleration speed (refers to the speed we reach after the automatic acceleration of the machine after pressing the acceleration button delay)
3 Automatic acceleration time (refers to the time required for the machine to automatically accelerate from zero speed to the design of the highest machine speed. The shorter the time setting, the faster the acceleration.)
8. Tension control: Set the tension of each discharge motor in the touch screen. The discharge motor mainly provides a reverse torque, generates tension on the paper surface, keeps the paper web flat, and the speed control of the discharge motor is a process of gradually increasing speed, but the line speed remains unchanged.
9. Each console has its own power switch, which can be switched on and off as needed.
10. The forward and reverse running buttons are set on the console, and the user can select the running direction according to the needs.
 

Led Tape Light

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.2 Longitudinal section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing. The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.
The high-speed rewinding paper conveying system is also very important in the application. The old-fashioned rewinding machine is mainly handled by manual. With the increase of the speed of the rewinding machine, the manual can no longer be processed. There are two ways to transport the paper side of the reel: fan direct pumping and venturi suction. The direct drawing type of the fan mainly uses a centrifugal fan, and the fan is placed under the floor. The inlet of the fan and the air duct near the longitudinal cutting edge are connected to each other, and the blade of the fan is also equipped with a wind blade. When the fan is sucked, it will be broken by the blade and then sent to the water pulper. However, since the edge of the paper has to pass through the inside of the fan, the blade transported by this type of paper is very worn and needs to be changed frequently. Venturi suction is also used in the high-pressure centrifugal fan, but the paper edge does not pass through the fan, directly the longitudinal cutting edge of the duct into the venturi pipe, the wind machine generates negative pressure in the venturi, and then the paper While washing the venturi tube and then feeding it to the water pulper, the paper edge conveyed at this time is continuous. The disadvantage of this method is that when the speed of the winder is relatively high, the power of the selected fan is large, which will increase the operation. Cost, increase loss.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com