Heat Resistant Tape

Heat Resistant Tape

Rewinding Machine safety operation guide - 

Third, the rewinding machine opening and closing operation sequence:
1. Start the rewinding machine and the paper edge blower motor to put the speed to the crawling speed. Tearing the web
Into one. The paper edge is wound into a roller according to the specified path, and the round paper web must be straightened. Loosen and tightly adjust, press the switch and the paper core tube to stick the tape. Stick the paper web to the paper core tube and start crawling. At the same time, the end of the paper roll is flat. The paper can not be wrinkled or discounted to ensure the quality of the rewinding. When the paper has broken ends, the joints are operated, the broken ends are connected and the joint quality is ensured.

Heat Resistant Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

Third, the function introduction
1. The tension control of the eject roller consists of a tension sensor and an eject motor.
In the loop control loop, the paper take-off motor is an electric motor when unwinding, and is a brake generator during normal operation and parking.
2. The pressure control of the pressure roller is controlled by various sensors such as the take-up roller diameter detecting sensor.
Forming a closed-loop control system, there are three pre-made curves for different paper grades and different finished paper diameters for the operator to choose, and the actuator will be controlled according to these three different pressure curves.
3, between the two take-up bottom rollers, take the torque difference control method, corresponding to no
The same take-up diameter, the torque between the front and rear bottom rollers is distributed in different proportions.

Heat Resistant Tape

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com