Hot Melt Tape

Hot Melt Tape

Rewinding Machine safety operation guide - 

Third, the rewinding machine opening and closing operation sequence:
1. Start the rewinding machine and the paper edge blower motor to put the speed to the crawling speed. Tearing the web
Into one. The paper edge is wound into a roller according to the specified path, and the round paper web must be straightened. Loosen and tightly adjust, press the switch and the paper core tube to stick the tape. Stick the paper web to the paper core tube and start crawling. At the same time, the end of the paper roll is flat. The paper can not be wrinkled or discounted to ensure the quality of the rewinding. When the paper has broken ends, the joints are operated, the broken ends are connected and the joint quality is ensured.

Hot Melt Tape

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

Hot Melt Tape

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad

AC drives were quickly successful in paper mills in Europe and Japan. Most major drive manufacturers now offer AC drives for paper mills. Most domestic paper mills use ABB, Siemens and other company's complete rewinder AC drive systems. . For example, the 6SE7O series speed control device of Siemens Company has achieved the speed control performance and has exceeded or exceeded the DC speed regulation performance and become the preferred solution for the transmission. The domestic rewinding machine AC drive started in the middle and late C9 of the 20th century. Due to the lack of understanding and research of the AC drive system of the winder, few mature sets of equipment were introduced to the market.
At present, in the domestic paper industry, the drive control system of the winder is gradually developing from the all-digital DC drive control system to the AC variable frequency drive control system. With the continuous improvement of the production process and speed of the rewinding machine, the requirements for real-time control and monitoring of the rewinding machine production process are becoming higher and higher. In order to reduce the large amount of wiring between the rewinding machine production site and the control room, the signal is improved. The transmission speed and quality of the fieldbus and human-machine interface began in the late 1990s for rewinders. Fieldbus is a new type of control system for all-digital, two-way communication. Due to the intelligent and digitized fieldbus devices, it fundamentally improves the accuracy of measurement and control and reduces transmission errors compared with analog signals. At the same time, due to the simplified structure of the system, the equipment and wiring are reduced, the internal functions of the field instrument are strengthened, the round-trip transmission of signals is reduced, and the operational reliability of the system is improved. In addition, the field control equipment has the ability of self-diagnosis and simple fault handling, and sends related equipment operation information and diagnostic maintenance information to the man-machine interface through digital communication. The user can monitor the running status of all equipments, query the cause of the fault, and Process parameters (such as tension) are set and modified according to the different requirements of the rewinder process. For this reason, the application of fieldbus technology and HMI technology to the winder has become the development trend of automatic control of the winder. With the continuous promotion of inverter, HMI technology and fieldbus technology in the application of winder and the combination of computer technology and communication technology, the design speed of the winder can reach 300om/min, the working speed is 2500m/min, and the winder Many of the manual operations have been automated, and manual operations have been greatly reduced. The degree of automation and control accuracy, control speed and system stability will be raised to a new level.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com