Custom Adhesive Tape

Custom Adhesive Tape

Rewinding Machine safety operation guide - 

Third, the rewinding machine opening and closing operation sequence:
1. Start the rewinding machine and the paper edge blower motor to put the speed to the crawling speed. Tearing the web
Into one. The paper edge is wound into a roller according to the specified path, and the round paper web must be straightened. Loosen and tightly adjust, press the switch and the paper core tube to stick the tape. Stick the paper web to the paper core tube and start crawling. At the same time, the end of the paper roll is flat. The paper can not be wrinkled or discounted to ensure the quality of the rewinding. When the paper has broken ends, the joints are operated, the broken ends are connected and the joint quality is ensured.

Custom Adhesive Tape

Automatic rewinding machine speed ratio adjustment method ---


        The rewinding machine is the first station of the production line equipment of the welcoming machine. The good running condition of the rewinding machine directly affects the quality and production efficiency of the post-processing welcoming paper. The rewinding machine should be able to operate normally and in a good production state. In addition to the good and non-damage of the components, the reasonable adjustment and control of the transmission ratio of the whole machine is very important.
        When the rewinding machine is produced, the original paper web is conveyed by five transmission rollers and belts, that is, a paper feeding belt, a curved roller, a rear platen roller, a front platen roller, a winding roller, and the like. Each of the base papers is thin, the elongation is limited, and the transmission speed ratio is unstable, and the paper web is easy to wrinkle and be broken during the continuous acceleration and deceleration operation of the winder. Reasonable adjustment and control of the speed of each drive roller and paper feed belt can greatly reduce the phenomenon that the paper web is broken. After many daily adjustments, the author summarizes the following key adjustment methods. 1. Stable paper feed belt conveys the line speed of the original paper web. The paper feeding belt of the rewinding machine is driven by the V-belt through the stepless speed-regulating wheel. When the output torque is large, the driving V-belt is close to the outer edge of the speed-regulating wheel, and the transmission speed will be more stable. In order to achieve such a stable transmission effect, the speed ratio of the main gearbox can be adjusted step by step to make the speed of the winding roller slower, and at the same time adjust the speed control handwheels of the paper feed belt of the original paper frame, so that the three sets of transmission triangle belts are in The outer edge of the stepless speed regulation wheel is in a reasonable position until the winding speed of the winding roller and the paper feeding belt are the same.

Custom Adhesive Tape

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad
Rewinding machine is an important papermaking machine. It is usually installed behind the paper machine. Its speed should be 2-3 times of the speed of the paper machine, generally 1500-1800m/min, up to 300om/min. When threading, run at a maximum speed of 1:100. In order to ensure continuous paper and loose paper during the rewinding process, the tension of the paper web must be kept constant; in order to ensure the tight and loose quality inside the finished paper, the load distribution of the front and rear bottom roller motors must be performed. Therefore, the main performance requirements of the rewinder for the electric drive system are long-term linear speed, adjustable speed and wide speed range, and fast response.
The control of the early rewinder is mainly based on DC drive, and the DC control system is composed of discrete components or analog regulators to realize the above control functions. Since the transmission of analog signals requires a one-to-one physical connection, the signal changes slowly, which increases the overhead of computer speed and accuracy, and the anti-interference ability of signal transmission is poor, and paper breakage and wrinkling often occur in the production process. So in the mid-to-late 1980s, the analog regulator was replaced by a digital regulator, and the DC digital control system of the winder appeared. This control system is more stable, reliable and suitable for maintenance than the analog system, and is more suitable for interface with the factory computer. In the mid-1990s, most of the newly-invested rewinders in the domestic paper industry used all-digital DC-speed converters produced abroad, and the more famous ones were the 6RA7O series from Siemens and the 590 series DC-speed converters from Continental Transmission.
Due to the DC motor commutator and the brush, under the stable conditions, the design speed of the winder can only reach 1800m/mni, and the accuracy of the digital regulator is still limited to about 0.08% of the maximum speed, which can not meet the high speed paper. The matching requirements of the machine (the speed of the winder should be 2-3 times the speed of the paper machine). In the early 1980s, European and Japanese developed AC variable frequency speed control devices. This technology was successfully introduced to the United States in the mid-1980s and used in rewinders. The biggest advantage of the AC drive is that the AC motor is simple in construction and reliable in operation, and it requires much less maintenance and repair than DC motors.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com