Rewinding Machine safety operation guide -
Third, the rewinding machine opening and closing operation sequence:
2. When the paper roll reaches the specified rewinding diameter (meters), the working speed will slowly drop.
After the paper roll reaches the specified diameter (meters), press the “stop” switch. After the quality inspector has measured the paper roll and the appearance quality, tape the outermost piece of paper with a tape and stick the paper. The inner core of the core barrel is pulled out (the thimble) and the bottom knife roll is lifted to remove the paper roll.
3, the rewinding machine should have a long downtime, stop the paper side fan, and do a good job of surrounding sanitation.
Guolian High Speed ??Slitting Rewinder Technical Description ---
Fourth, performance guarantee
1. Ensure that the winder is brand new, unused, using the latest design and suitable materials
Manufactured, and in all respects meets the quality, specifications and performance of the contract.
2. Ensure that the production line has been properly guided to install and adjust to achieve product economics and technical means.
3, the seller guarantees that the rotating components will not affect the running performance, paper quality, equipment can
Responsive or maintenance vibration.
4. The vibration guarantee is valid only when the basis of the winder is designed according to the requirements of the seller. 5. Mechanical guarantees do not include natural wear and consumables and consumables.
6. Selling due to improper storage, transportation, installation, maintenance and operation by the buyer
The party is not responsible. The buyer’s modification of the equipment is not guaranteed by the seller.
Belt rewinding machine design and working principle ---
3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc