Custom Packing Tape

Custom Packing Tape

Rewinding Machine safety operation guide - 

Third, the rewinding machine opening and closing operation sequence:

2. When the paper roll reaches the specified rewinding diameter (meters), the working speed will slowly drop.
After the paper roll reaches the specified diameter (meters), press the “stop” switch. After the quality inspector has measured the paper roll and the appearance quality, tape the outermost piece of paper with a tape and stick the paper. The inner core of the core barrel is pulled out (the thimble) and the bottom knife roll is lifted to remove the paper roll.
3, the rewinding machine should have a long downtime, stop the paper side fan, and do a good job of surrounding sanitation.

Custom Packing Tape

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

Custom Packing Tape

Design and application of constant tension and load distribution control for winder---

1. Rewinder structure and working principle

1.1 Structure
The rewinder is generally composed of a unwinding roll (also referred to as a paper take-off roll), a guide roll, a slitting mechanism, a platen roll, a take-up bottom roll (including a front bottom roll and a rear bottom roll), and a double bottom roll. The machine is characterized by two rotating drums to replace and support the take-up reel, usually with or without a rotating platen roller pressed against the top of the reel in the take-up, the take-up reel is taken up The main structure (has become the front and rear bottom rollers respectively). Under normal circumstances, the surface of the front bottom roller is rough, and the surface of the rear bottom roller is relatively smooth. They are connected to the motor through the reduction gear box. The platen roller, also called the load roller, acts to create a downward pressure whose pressure is the difference between its own weight and the load roller lifting pressure. The unwinding roller is composed of a leg paper holder, a unwinding roller coupling, a unwinding roller clamping mechanism, and a unwinding motor. Longitudinal cutters generally have book holders side by side on the same axis, mainly used to cut off the change. Cut a certain width of sheet paper to the required width as needed. Two tension sensors are placed on the tension roller to receive the web tension.

 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com