Kraft Paper Gummed Tape

Kraft Paper Gummed Tape

Rewinding Machine safety operation guide - 

Fifth, the tool change operation:
1. The bottom knife replacement is handled by the mechanic.
2. The rewinding machine must be stopped when the upper round knife is replaced.
3. After removing the round blade, replace the new blade and fix it.
4. Install the round knife seat, adjust the angle, and lower the round knife to make it close to the bottom knife.
5, running, paper test knife, paper edge is not, smooth.
6. The tightness and depth of the blade and the bottom knife should be controlled properly, not too tight, otherwise the new knife
The film will roll the knife; it should not be too loose, otherwise it will jump the knife and the hair; not too deep, otherwise it will cause double trimming; too shallow will jump the knife.

Kraft Paper Gummed Tape

Rewinding Machine operation safety regulations - 

Fourth, other requirements in the production process
1. Rolling paper or paper jam of a certain part of the machine must be stopped. Use the jog function to remove the paper. The original paper should be carefully operated when it passes through the embossing device, the crimping device, the paper feed roller and the punching knife. It is strictly prohibited when the machine is running. Wipe and refuel the rotating parts in the state to avoid injury accidents;
2. During the production process, the gears, pulleys, chains and other components of the machine must not be allowed to entangle with paper scraps, ropes, etc., and the air pipe must not leak. The trachea, electric wires, etc. can not be fixed with rope or adhesive tape, which affects the appearance;

3. The waste paper can not be thrown anywhere in the production process, must be loaded into the designated waste paper bag to keep the production site clean.
4. The original paper core produced during the production process must be placed in the designated place;

Kraft Paper Gummed Tape

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.2 Longitudinal section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing. The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.
The high-speed rewinding paper conveying system is also very important in the application. The old-fashioned rewinding machine is mainly handled by manual. With the increase of the speed of the rewinding machine, the manual can no longer be processed. There are two ways to transport the paper side of the reel: fan direct pumping and venturi suction. The direct drawing type of the fan mainly uses a centrifugal fan, and the fan is placed under the floor. The inlet of the fan and the air duct near the longitudinal cutting edge are connected to each other, and the blade of the fan is also equipped with a wind blade. When the fan is sucked, it will be broken by the blade and then sent to the water pulper. However, since the edge of the paper has to pass through the inside of the fan, the blade transported by this type of paper is very worn and needs to be changed frequently. Venturi suction is also used in the high-pressure centrifugal fan, but the paper edge does not pass through the fan, directly the longitudinal cutting edge of the duct into the venturi pipe, the wind machine generates negative pressure in the venturi, and then the paper While washing the venturi tube and then feeding it to the water pulper, the paper edge conveyed at this time is continuous. The disadvantage of this method is that when the speed of the winder is relatively high, the power of the selected fan is large, which will increase the operation. Cost, increase loss.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com