Reinforced Aluminum Foil Tape

Reinforced Aluminum Foil Tape

Rewinding Machine safety operation guide - 

Fifth, the tool change operation:
1. The bottom knife replacement is handled by the mechanic.
2. The rewinding machine must be stopped when the upper round knife is replaced.
3. After removing the round blade, replace the new blade and fix it.
4. Install the round knife seat, adjust the angle, and lower the round knife to make it close to the bottom knife.
5, running, paper test knife, paper edge is not, smooth.
6. The tightness and depth of the blade and the bottom knife should be controlled properly, not too tight, otherwise the new knife
The film will roll the knife; it should not be too loose, otherwise it will jump the knife and the hair; not too deep, otherwise it will cause double trimming; too shallow will jump the knife.

Reinforced Aluminum Foil Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

4, the coiling department:
Mainly by frame, bottom roller device, pressure roller device, head lifting device, paper core plug clamping device, head lifting device, paper roller ejector, cutting knife, automatic paper web clamping device, automatic paper changing device, paper Core positioning device, paper unloading table device, paper stop roller device and perfect safety protection system.
       The frame structure is welded with high-quality steel and is heavy and strong.
       The bottom roller device is composed of front and rear bottom rollers, hydraulic disc brakes, motors, reducers and the like. The bottom roller adopts SKF bearing and Q345 coil processing. The front and bottom rollers are sprayed with tungsten carbide and the thickness is 0.08mm. The rear bottom roller has a special spiral groove composed of three spiral curves, and the outer diameter is φ850mm.
       The pressure roller is mounted on the pressure roller beam with a diameter of φ290mm. It is made of seamless steel tube and has a chrome plated surface. It is divided into two sections and is driven by a double motor via a belt. Both ends of the pressure roller beam are equipped with a synchronizing device and a safety locking ratchet, a roller position fine adjustment device, and a pressure sensor and a displacement potentiometer for measuring the diameter of the winding roller. The wear-reducing roller is mounted on both ends to contact the guide rail to minimize the friction. The up and down movement is directly driven by a large stroke hydraulic cylinder, and the pressure roller re-pressing device adopts an imported servo valve to realize automatic control of the whole process of the pressure of the pressure roller, and the control precision is high, and the pressure value can be automatically adjusted according to the difference of the roller diameter. The platen roller is equipped with a variety of pressure programs that can be selected by the user depending on the type of paper. In special cases, manual operation is possible. On the basis of the adjustment by the pressure roller, according to the increase of the roller diameter, the torque difference between the two bottom rollers is automatically changed, and the inner tightness of the appropriate finished paper roller is obtained.
       The head lifting device is directly controlled by the hydraulic cylinder to move up and down along the guide rail. When the paper is normally wound, the hydraulic cylinder pulling force only offsets the gravity and friction force, so that the radial force of the paper core is reduced as much as possible.
       The paper core clamping device uses a cylinder to clamp the paper core to prevent axial movement of the paper core during the winding process. It also has a handwheel adjustment mechanism that fine-tunes the position of the core.
      The paper core holding device rotates around the center of the front bottom roller, and the paper core is fed by the automatic paper feed core device, and the paper core is pushed into the robot slot in the holding device. After the roll of the paper roll is completed, the web holding device is raised, and the web is pressed against the back bottom roll to maintain the tension of the web. The paper roll ejector pushes the paper roll away from the rear bottom roll, and the cutting knife quickly pops up to cut the paper web. At the same time, the paper roll ejector smoothly pushes the paper roll into the paper discharge hopper. Then, the automatic paper changer device is raised, a new paper core is placed, and under the synergistic action of the air nozzle, the paper head is automatically wound into the paper core to complete the paper core replacement and the next roll paper is carried out.
     The core positioning device is located in front of the front bottom roller. On the operating side, the cylinder is driven with a ruler and when the core is pushed in, it is dimensioned to match the size of the front cut.
Both the paper roll ejector and the unloading table are hydraulically driven and controlled, and the action runs smoothly. The unloader has side guards.
The paper stop roller frame device is located in front of the finished paper roll, and prevents various dangers to people and equipment caused by various reasons such as sudden flight of the paper roll during normal operation. It is mainly composed of a bracket, a synchronizing device, a safety locking ratchet and the like. Directly driven by the cylinder, the safety lock ratchet is automatically controlled by the cylinder to prevent the paper stop roller frame from falling suddenly due to unexpected events such as oil leakage.
Safety protection system, including a large number of limit switches, safety doors, interlocking photoelectric protection devices, various locking mechanisms, warning signs, etc.

Reinforced Aluminum Foil Tape

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com