Tape In Human Hair Extensions

Tape In Human Hair Extensions

Rewinding Machine safety operation guide - 

Fifth, the tool change operation:
1. The bottom knife replacement is handled by the mechanic.
2. The rewinding machine must be stopped when the upper round knife is replaced.
3. After removing the round blade, replace the new blade and fix it.
4. Install the round knife seat, adjust the angle, and lower the round knife to make it close to the bottom knife.
5, running, paper test knife, paper edge is not, smooth.
6. The tightness and depth of the blade and the bottom knife should be controlled properly, not too tight, otherwise the new knife
The film will roll the knife; it should not be too loose, otherwise it will jump the knife and the hair; not too deep, otherwise it will cause double trimming; too shallow will jump the knife.

Tape In Human Hair Extensions

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

Tape In Human Hair Extensions

Design and application of constant tension and load distribution control for winder---

2. Main research content
(1) On the basis of understanding the working principle and production process of the rewinder, determine the AC drive configuration scheme of the rewinder and the common DC bus power supply mode.
(2) In view of the influence of the change of the winding diameter on the tension during the rewinding process and the phenomenon of paper break and loose paper during acceleration and deceleration, a composite tension control method combining direct tension and indirect tension is proposed, and the real-time calculation and dynamics of the winding diameter are designed. Torque compensation program that effectively corrects tension disturbances to ensure constant tension during rewinding
(3) Software and hardware design to complete the pressure control of the platen roller”

(4) After detailed analysis of the causes of the load distribution of the bottom roller motor before and after the detailed analysis, determine the master-slave control scheme of the two motors, design the load distribution control system.
(5) Establishing a profibus-Dp network system, designing communication between pLC and inverter! Op operation panel"

(6) Using STEP7 to design the software of the rewinder control system, using ProTool to compile the entire monitoring system screen"

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com