Custom Washi Tape Printing

Custom Washi Tape Printing

Rewinding Machine safety operation guide - 

Sixth, change the specification operation:
1. Stop the winder and lift the round knife and tighten the bolts on the base of the round knife.
2. Move the base of the circular knife holder and measure the distance between two adjacent circular cutters with a tape measure to make it conform to
Paper specification requirements.
3. Fix the base of the round knife holder, tighten the bolts, and measure the specifications once again.
Dynamic rewinding (contact angle, tightness, depth).

Custom Washi Tape Printing

Guolian High Speed ??Slitting Rewinder Technical Description ---

Part II: Hydraulic and pneumatic parts:
1. Hydraulic part:
The local hydraulic system consists of a hydraulic pump station and a valve station. System control and transmission components use world famous brand products. All hydraulic lines of the winder are supplied.
The hydraulic pump station uses three oil pumps to provide pressure oil source. The hydraulic station has safety facilities such as liquid level alarm, temperature control, filter blockage alarm, and a set of circulating filtration and cooling system. The valve station control section includes:
1) Ejection shaft ejection and locking device 2) Ejection frame movement 3) Ejection shaft clutch
4) Hook protection device 5) Paper core plug locking device 6) Press roller load reducing device
7) Unloader unit 8) Push roller unit 9) Stop roller holder lifting device
10) Ejection shaft hydraulic disc brake 11) Guide roller hydraulic disc brake
12) Front and rear bottom roller hydraulic disc brakes 13) Head lifting device.
14) Paper core positioning device 15) Paper head clamping lifting device
16) Automatic paper changer lifting device
The hydraulic circuit has the following features:
A. This system adopts superimposed valve, which is simple and compact in structure, convenient in maintenance and installation, and strong in work reliability;
B. The paper return shaft, the guide roller and the two bottom rollers are equipped with hydraulic disc brakes, which assist the brake during emergency braking and share part of the braking torque. Reduce the braking load of the motor, increase reliability, and install an accumulator;

Custom Washi Tape Printing

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com