Cotton Twill Tape

Cotton Twill Tape

Rewinding Machine safety operation guide - 

Seventh, production operations and quality control during the rewinding process:
1. The speed must be slow when rewinding, and the inspector should check the appearance quality of the paper.
2, often check the quality of the paper, found that the paper disease stopped in time, to the inspector on duty
Report and contact the upper and lower processes to strip off paper with quality problems. The rewinding can be continued after the inspector confirms.
3. When rewinding, pay attention to the situation of broken ends, trimming, etc., and control the tension of the paper during rewinding.
The car is tight) to keep the inner and outer tension of the paper roll consistent.

Cotton Twill Tape

Rewinding Machine safety operation guide - 

Seventh, production operations and quality control during the rewinding process:

4, pay attention to the quality of the rewinding of the paper roll when rewinding, found zigzag, knife, running,
If the color difference is serious, skipping, chain printing, wrinkling, violent edge, etc., the result should be stopped in time. Only after the inspector confirms can the machine be re-rolled.
5. When the rewinding operation is running, the host must be at the console, and must not leave at will to prevent accidents. Transport
The speed of lifting and lowering is slow, and the speed of the vehicle cannot exceed the prescribed limit.
6. When loading the paper core tube, it is necessary to select the paper core with the same outer diameter and the length specification in line with the quality standard.
The installation of the cylinder requires a large deviation of the outer diameter and needs to be replaced.

Cotton Twill Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
      Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
      The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com