Gummed Paper Tape

Gummed Paper Tape

Rewinding Machine safety operation guide - 

Seventh, production operations and quality control during the rewinding process:
1. The speed must be slow when rewinding, and the inspector should check the appearance quality of the paper.
2, often check the quality of the paper, found that the paper disease stopped in time, to the inspector on duty
Report and contact the upper and lower processes to strip off paper with quality problems. The rewinding can be continued after the inspector confirms.
3. When rewinding, pay attention to the situation of broken ends, trimming, etc., and control the tension of the paper during rewinding.
The car is tight) to keep the inner and outer tension of the paper roll consistent.

Gummed Paper Tape

Automatic rewinding machine speed ratio adjustment method ---

2. Adjust the paper-pressing gap of the platen roller so that the paper web can be smoothly conveyed between the paper feeding belt and the winding roller. The rear platen roller is the intermediate link of the paper web conveying process. If the adjusted gap is too small, the paper web is easy to wrinkle and sag. When the gap is too large, the three layers of paper are not combined together to facilitate delamination and fault, which affects the speed of the paper feed and Rewind quality. When adjusting the paper-pressing roller, the paper-pressing gap should be gradually increased from small to large, so that the paper web can be locked without sag and not drooping.

Gummed Paper Tape

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad

AC drives were quickly successful in paper mills in Europe and Japan. Most major drive manufacturers now offer AC drives for paper mills. Most domestic paper mills use ABB, Siemens and other company's complete rewinder AC drive systems. . For example, the 6SE7O series speed control device of Siemens Company has achieved the speed control performance and has exceeded or exceeded the DC speed regulation performance and become the preferred solution for the transmission. The domestic rewinding machine AC drive started in the middle and late C9 of the 20th century. Due to the lack of understanding and research of the AC drive system of the winder, few mature sets of equipment were introduced to the market.
At present, in the domestic paper industry, the drive control system of the winder is gradually developing from the all-digital DC drive control system to the AC variable frequency drive control system. With the continuous improvement of the production process and speed of the rewinding machine, the requirements for real-time control and monitoring of the rewinding machine production process are becoming higher and higher. In order to reduce the large amount of wiring between the rewinding machine production site and the control room, the signal is improved. The transmission speed and quality of the fieldbus and human-machine interface began in the late 1990s for rewinders. Fieldbus is a new type of control system for all-digital, two-way communication. Due to the intelligent and digitized fieldbus devices, it fundamentally improves the accuracy of measurement and control and reduces transmission errors compared with analog signals. At the same time, due to the simplified structure of the system, the equipment and wiring are reduced, the internal functions of the field instrument are strengthened, the round-trip transmission of signals is reduced, and the operational reliability of the system is improved. In addition, the field control equipment has the ability of self-diagnosis and simple fault handling, and sends related equipment operation information and diagnostic maintenance information to the man-machine interface through digital communication. The user can monitor the running status of all equipments, query the cause of the fault, and Process parameters (such as tension) are set and modified according to the different requirements of the rewinder process. For this reason, the application of fieldbus technology and HMI technology to the winder has become the development trend of automatic control of the winder. With the continuous promotion of inverter, HMI technology and fieldbus technology in the application of winder and the combination of computer technology and communication technology, the design speed of the winder can reach 300om/min, the working speed is 2500m/min, and the winder Many of the manual operations have been automated, and manual operations have been greatly reduced. The degree of automation and control accuracy, control speed and system stability will be raised to a new level.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com