Adhesive Packaging Tape

Adhesive Packaging Tape

Rewinding Machine safety operation guide - 

Seventh, production operations and quality control during the rewinding process:

7. The tape must be kept in accordance with the regulations. When the head is reconnected, the tape outside the broken head must be
Take out in time, it is forbidden to mix the tape into the damaged paper, pay attention to the rewinding equipment, the running condition, find the problem and stop the contact and deal with it in time to prevent the quality of the rewinding.
8. The paper machine has a long downtime and works well with the paper machine.

Adhesive Packaging Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

Part II: Hydraulic and pneumatic parts:
1. Hydraulic part:
The local hydraulic system consists of a hydraulic pump station and a valve station. System control and transmission components use world famous brand products. All hydraulic lines of the winder are supplied.
The hydraulic pump station uses three oil pumps to provide pressure oil source. The hydraulic station has safety facilities such as liquid level alarm, temperature control, filter blockage alarm, and a set of circulating filtration and cooling system. The valve station control section includes:
1) Ejection shaft ejection and locking device 2) Ejection frame movement 3) Ejection shaft clutch
4) Hook protection device 5) Paper core plug locking device 6) Press roller load reducing device
7) Unloader unit 8) Push roller unit 9) Stop roller holder lifting device
10) Ejection shaft hydraulic disc brake 11) Guide roller hydraulic disc brake
12) Front and rear bottom roller hydraulic disc brakes 13) Head lifting device.
14) Paper core positioning device 15) Paper head clamping lifting device
16) Automatic paper changer lifting device
The hydraulic circuit has the following features:
A. This system adopts superimposed valve, which is simple and compact in structure, convenient in maintenance and installation, and strong in work reliability;
B. The paper return shaft, the guide roller and the two bottom rollers are equipped with hydraulic disc brakes, which assist the brake during emergency braking and share part of the braking torque. Reduce the braking load of the motor, increase reliability, and install an accumulator;

Adhesive Packaging Tape

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com