Coloured Tape

Coloured Tape

Rewinding Machine operating procedures - 

First, the boot process:
1. Turn on the total power of the rewinder and the power of the detection system in turn; Note: (1) Before turning on the power, please make sure that the circuit is connected correctly and there is no short circuit;
(2) When the main power is turned on, an alarm will occur. After about 5 seconds, after resetting through the touch screen, turn on the detection power.
2. Turn on the air source switch, please ensure that the air pressure is around 6Mpa;
3. According to the paper-feeding direction in the machine state of the touch screen, the product is paper-punched; Note: (1) Please select the paper-feeding state before putting on paper;
(2) Ensure that the core is in the middle position of the inflation shaft, and the core is installed on the left and right gas rise shaft
The same location;

Coloured Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

3. Double curved roller section:
Mainly composed of bracket, double arc roller, worm gear adjustment device, angle gear, air motor and other devices
        After cutting the paper, it enters a set of curved roller stretching assembly, which is mainly composed of two curved rollers and an adjusting mechanism. The adjusting mechanism is driven by a pneumatic motor, and through a set of angular gear mechanism and two sets of worm gear reduction mechanisms, according to The wrap angle between the web and the curved roller needs to be adjusted at any time. The curved roller is introduced from abroad to ensure its performance. This system effectively stretches the web, eliminates wrinkles, and separates the paper rolls.
4. Automatic paper feeding department:
The guiding paper-feeding roller and the compressed air and the guiding plate are adopted, so that the paper head can smoothly and quickly and accurately complete the paper-feeding action on the uniform air cushion generated by the guiding plate and the compressed air, and between the two bottom rollers is used between the conveyor belt and the bottom roller. Friction drive, so that the paper head is close to the surface of the bottom roller, and the paper-feeding action is completed under the action of compressed air.

Coloured Tape

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com