Cello Tape

Cello Tape

Rewinding Machine operating procedures - 

First, the boot process:
1. Turn on the total power of the rewinder and the power of the detection system in turn; Note: (1) Before turning on the power, please make sure that the circuit is connected correctly and there is no short circuit;
(2) When the main power is turned on, an alarm will occur. After about 5 seconds, after resetting through the touch screen, turn on the detection power.
2. Turn on the air source switch, please ensure that the air pressure is around 6Mpa;
3. According to the paper-feeding direction in the machine state of the touch screen, the product is paper-punched; Note: (1) Please select the paper-feeding state before putting on paper;
(2) Ensure that the core is in the middle position of the inflation shaft, and the core is installed on the left and right gas rise shaft
The same location;

Cello Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

Part II: Hydraulic and pneumatic parts:
1. Hydraulic part:
The local hydraulic system consists of a hydraulic pump station and a valve station. System control and transmission components use world famous brand products. All hydraulic lines of the winder are supplied.
The hydraulic pump station uses three oil pumps to provide pressure oil source. The hydraulic station has safety facilities such as liquid level alarm, temperature control, filter blockage alarm, and a set of circulating filtration and cooling system. The valve station control section includes:
1) Ejection shaft ejection and locking device 2) Ejection frame movement 3) Ejection shaft clutch
4) Hook protection device 5) Paper core plug locking device 6) Press roller load reducing device
7) Unloader unit 8) Push roller unit 9) Stop roller holder lifting device
10) Ejection shaft hydraulic disc brake 11) Guide roller hydraulic disc brake
12) Front and rear bottom roller hydraulic disc brakes 13) Head lifting device.
14) Paper core positioning device 15) Paper head clamping lifting device
16) Automatic paper changer lifting device
The hydraulic circuit has the following features:
A. This system adopts superimposed valve, which is simple and compact in structure, convenient in maintenance and installation, and strong in work reliability;
B. The paper return shaft, the guide roller and the two bottom rollers are equipped with hydraulic disc brakes, which assist the brake during emergency braking and share part of the braking torque. Reduce the braking load of the motor, increase reliability, and install an accumulator;

Cello Tape

Belt rewinding machine design and working principle ---

12Paper roll holder
When the paper roll is stopped, the paper roll is fixed at a certain position by the paper roll holder. The paper roll holder prevents slack and lateral movement of the paper roll. It is important to make a joint when making a customer roll. Roll holder on the take-up roll
The paper roll holder on the paper roll includes a spring-loaded plastic roll mounted on the paper cutter frame. When the paper cutter is in or on the middle position, the paper roll holder is placed against the surface of the rear bottom roller.


13 Automatic roll change
The rewinding device removes the paper roll from the winder.
The rewinding device cuts the sheet, pushes the paper roll onto the unloading station and fills in a new core for the rewinding.
The roll change can be started when the roll is decelerated. In the final stage of deceleration, the nipple guardrail and the platen roller rise to a high position. The unloader rises to the position where the paper roll is received. When the winder stops, the paper core clamp opens and rises to rise. The paper cutter is raised from between the paper rolls. The paper feed roller pushes the paper roll to the paper unloading station. At the same time, the paper cutter cuts the paper. The vacuum suction of the rear bottom roller sucks the cut sheet onto the roller. The core loader drops the new core onto the roll. The paper feed roller returns to its original position and the unloading table falls to the middle position. The paper core clip is lowered and closed. The platen roller and the nip guard are lowered. The winder crawls at a speed.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com