Strong Tape

Strong Tape

Rewinding Machine operation safety regulations - 

Fourth, other requirements in the production process
1. Rolling paper or paper jam of a certain part of the machine must be stopped. Use the jog function to remove the paper. The original paper should be carefully operated when it passes through the embossing device, the crimping device, the paper feed roller and the punching knife. It is strictly prohibited when the machine is running. Wipe and refuel the rotating parts in the state to avoid injury accidents;
2. During the production process, the gears, pulleys, chains and other components of the machine must not be allowed to entangle with paper scraps, ropes, etc., and the air pipe must not leak. The trachea, electric wires, etc. can not be fixed with rope or adhesive tape, which affects the appearance;

3. The waste paper can not be thrown anywhere in the production process, must be loaded into the designated waste paper bag to keep the production site clean.
4. The original paper core produced during the production process must be placed in the designated place;

Strong Tape

Automatic rewinding machine speed ratio adjustment method ---


        The rewinding machine is the first station of the production line equipment of the welcoming machine. The good running condition of the rewinding machine directly affects the quality and production efficiency of the post-processing welcoming paper. The rewinding machine should be able to operate normally and in a good production state. In addition to the good and non-damage of the components, the reasonable adjustment and control of the transmission ratio of the whole machine is very important.
        When the rewinding machine is produced, the original paper web is conveyed by five transmission rollers and belts, that is, a paper feeding belt, a curved roller, a rear platen roller, a front platen roller, a winding roller, and the like. Each of the base papers is thin, the elongation is limited, and the transmission speed ratio is unstable, and the paper web is easy to wrinkle and be broken during the continuous acceleration and deceleration operation of the winder. Reasonable adjustment and control of the speed of each drive roller and paper feed belt can greatly reduce the phenomenon that the paper web is broken. After many daily adjustments, the author summarizes the following key adjustment methods. 1. Stable paper feed belt conveys the line speed of the original paper web. The paper feeding belt of the rewinding machine is driven by the V-belt through the stepless speed-regulating wheel. When the output torque is large, the driving V-belt is close to the outer edge of the speed-regulating wheel, and the transmission speed will be more stable. In order to achieve such a stable transmission effect, the speed ratio of the main gearbox can be adjusted step by step to make the speed of the winding roller slower, and at the same time adjust the speed control handwheels of the paper feed belt of the original paper frame, so that the three sets of transmission triangle belts are in The outer edge of the stepless speed regulation wheel is in a reasonable position until the winding speed of the winding roller and the paper feeding belt are the same.

Strong Tape

Belt rewinding machine design and working principle ---

 

9 small paper rolls launched
The small paper roll ejecting device is used for those paper rolls that are too small for the paper feed roller. The small paper roll ejecting device is mounted on the paper feed roller. It relies on hydraulic pressure to move. The minimum diameter that the small paper roll exit can be pushed out is 200 mm (7.9 in).


10 paper cutter construction
The paper cutter is a zigzag blade, which cuts the slit webs during roll ejection. The paper cutter rises from the paper roll to the paper cutting position. The movement of the paper cutter is done by a lever driven by a hydraulic cylinder.
working principle 
The paper roll is pressed against the raised paper cutting blade by the ejector pin and cut.


11 core positioning pin
The end of the core loader is a paper core locating pin attached to the rewinder frame. The paper core positioning pin includes a metal plate and a frame. The scale on the core locating pin shows the position of the locating pin. The paper core locating pin holds the paper core in the correct position on the core loader only by the edge of the slitter. The core positioning pin is placed in close proximity to the slit and is locked in that position by the locking arm.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com