Hockey Tape Machine

Hockey Tape Machine

Rewinder mechanical structure and control process ---

 

I. Overview of the double-roller under the paper rewinding machine
The mechanical structure of the lower paper rewinding machine is shown in Figure 2-1. It can be seen from the mechanical structure diagram of the rewinding machine that the lower paper rewinding machine is fed into the paper web from below the rewinding machine. The paper web is wound around a support roll and then rolled up with a roll of paper. The paper is ejected from the unwinding roll, passed through the lower transfer roll, and then the web passes through the slitting mechanism at a fixed position, bypassing the front backup roll (press The second roller in the direction of the paper line or the back support roller is then wound on the take-up reel.
During the rewinding process, the paper web passes through the eject roller, and the tension force formed by the paper web pulls the paper roll toward the support roller, and the tension of the paper roll is stabilized by the action of the tension, and the rewinding machine can be made at a high speed roll. The quality of the paper roll can be guaranteed when taken. The lower thread rewinding machine can also control the pressure between the platen roller and the paper roll by changing the transmission torque difference of the two supporting rollers, so that the pressure of the finished paper roll can be controlled, and the quality of the paper roll can be Do a good job of control.
It can be seen from the figure that since the slitting mechanism of the lower threader rewinding machine is installed at a fixed position, this can avoid axial sway during the rewinding process, and also facilitates the control of the winding of the paper roll. The role of most of these rewinders in the Middle East is not very high, very close to the ground, the center of gravity, relatively low, due to the lower center of gravity, the rewinder can remain stable at high speeds, so this Types of rewinding machines are widely used, and most of the paper mills in China use the lower thread rewinding machine. Through many practices, this rewinding machine is also the best performance. And its speed can reach 2,500 meters per minute, the width is also long, can reach 10 meters, can handle the rewinding of different types of paper, from low basis to cardboard can be re-rolled. Of course, it also has its own shortcomings. The disadvantage is that because it is close to the ground, it is not easy for the operator to access the bottom of the machine. It is also difficult to guide the paper. Therefore, when the mechanical equipment is installed, a pit will be placed under the machine. In order to make the operator more accessible, the high-grade rewinding adopts the automatic threading structure, and there is no such problem.

Hockey Tape Machine

Design and application of constant tension and load distribution control for winder---

4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.

Hockey Tape Machine

Belt rewinding machine design and working principle ---

14 change roll
The roll change blower is used to blow the cut sheet onto the core. On the platen roller, there are three blowing tubes on the paper core with a blowing tube under the paper core. When blasting is used, the paper will bypass the core at the beginning of the machine.


15 paper cut hair dryer
The web cut blower is used when the web must be cut quickly. The blow tube is located between the guide rollers.
The blow tube is activated by a safety photocell or a manually transmitted pulse signal.
1- Spreading roller
2- Adjust the paper wrap angle device,
3- Stretch roller bending direction adjustment device
A- paper web
B- First stretch roll bending direction
C- second stretch roll bending direction
Stretching device
The stretching device on the illustration is the basic position of the display. The web A passes directly through the spreader roll, which means that the web curvature is zero. The first spreader roll B is at an angle of 90 degrees with respect to the sheet. The second spreader roll has a camber at the base position when the cylinder pressure is 0 bar. The cylinder pressure can be read on the meter at the location of the control system.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com