Tape Dispensing Machine

Tape Dispensing Machine

Rewinder mechanical structure and control process ---

 

I. Overview of the double-roller under the paper rewinding machine
The mechanical structure of the lower paper rewinding machine is shown in Figure 2-1. It can be seen from the mechanical structure diagram of the rewinding machine that the lower paper rewinding machine is fed into the paper web from below the rewinding machine. The paper web is wound around a support roll and then rolled up with a roll of paper. The paper is ejected from the unwinding roll, passed through the lower transfer roll, and then the web passes through the slitting mechanism at a fixed position, bypassing the front backup roll (press The second roller in the direction of the paper line or the back support roller is then wound on the take-up reel.
During the rewinding process, the paper web passes through the eject roller, and the tension force formed by the paper web pulls the paper roll toward the support roller, and the tension of the paper roll is stabilized by the action of the tension, and the rewinding machine can be made at a high speed roll. The quality of the paper roll can be guaranteed when taken. The lower thread rewinding machine can also control the pressure between the platen roller and the paper roll by changing the transmission torque difference of the two supporting rollers, so that the pressure of the finished paper roll can be controlled, and the quality of the paper roll can be Do a good job of control.
It can be seen from the figure that since the slitting mechanism of the lower threader rewinding machine is installed at a fixed position, this can avoid axial sway during the rewinding process, and also facilitates the control of the winding of the paper roll. The role of most of these rewinders in the Middle East is not very high, very close to the ground, the center of gravity, relatively low, due to the lower center of gravity, the rewinder can remain stable at high speeds, so this Types of rewinding machines are widely used, and most of the paper mills in China use the lower thread rewinding machine. Through many practices, this rewinding machine is also the best performance. And its speed can reach 2,500 meters per minute, the width is also long, can reach 10 meters, can handle the rewinding of different types of paper, from low basis to cardboard can be re-rolled. Of course, it also has its own shortcomings. The disadvantage is that because it is close to the ground, it is not easy for the operator to access the bottom of the machine. It is also difficult to guide the paper. Therefore, when the mechanical equipment is installed, a pit will be placed under the machine. In order to make the operator more accessible, the high-grade rewinding adopts the automatic threading structure, and there is no such problem.

Tape Dispensing Machine

Design and application of constant tension and load distribution control for winder---

2. Main research content
(1) On the basis of understanding the working principle and production process of the rewinder, determine the AC drive configuration scheme of the rewinder and the common DC bus power supply mode.
(2) In view of the influence of the change of the winding diameter on the tension during the rewinding process and the phenomenon of paper break and loose paper during acceleration and deceleration, a composite tension control method combining direct tension and indirect tension is proposed, and the real-time calculation and dynamics of the winding diameter are designed. Torque compensation program that effectively corrects tension disturbances to ensure constant tension during rewinding
(3) Software and hardware design to complete the pressure control of the platen roller”

(4) After detailed analysis of the causes of the load distribution of the bottom roller motor before and after the detailed analysis, determine the master-slave control scheme of the two motors, design the load distribution control system.
(5) Establishing a profibus-Dp network system, designing communication between pLC and inverter! Op operation panel"

(6) Using STEP7 to design the software of the rewinder control system, using ProTool to compile the entire monitoring system screen"

Tape Dispensing Machine

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com