Copper Tape Machine

Copper Tape Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder
2.1 Ejection Department
In the rewinder system, we installed the paper roll on the paper exit frame. In order to ensure that the width of the sides of the paper web is the same, we should be moving the seasoning when the paper roll is ejected. However, the paper roll in the new structure can be moved together with the paper exit frame, which ensures greater rigidity of the paper exit frame. In addition to manually moving the paper roll, we can also use the pneumatic, photoelectric device and electric method to adjust the axial movement of the paper exit frame, so that the cutting edge of the winder can be narrowed, and the manual adjustment can not be achieved. Requirements.
We have a coupling on the reel of the unwinding roll. When working, we can use a pneumatic device to connect the brake to the motor. We can know that when the high-speed winder is started, the required acceleration time from zero to 2000m/min can be completed within 50~60s, and the deceleration time required for braking is 40s. Or even shorter, so we need to consider the maximum diameter and the maximum braking speed of the paper-removing brake on the winder to reduce the paper loss of the paper-cut, or it will cause a lot of waste. In the selection of the brakes of the eject roll, we often use brakes for starting brakes, magnetic brakes and mechanical brakes. In the usual case, we use the combination of the brake motor and other brake devices. When we press the paper, the paper roll started by the DC motor can enter the acceleration and working state and can be operated by the braking of the DC motor. Control, the tension control of the paper web, in the case of emergency stop, we can use the DC motor and other brakes together to stop the paper roll at the fastest speed.

Copper Tape Machine

Design and application of constant tension and load distribution control for winder---

1. Rewinder structure and working principle

1.2 Working principle
The paper web is taken out from the paper take-off roller (in this paper, the lower paper feeding method is adopted), and the paper guide roller passes through the slitting mechanism, and is wound from the bottom between the front and rear bottom rollers, and then wound on the paper core. There are 1 support rollers in front of and behind the slitting mechanism, and the front and rear support rollers are equipped with tension sensors for measuring the tension of the web. The platen roller above the core ensures the hardness of the roll. Each component of the winder is driven by a separate motor. The working principle is 3: the original paper roll taken from the paper machine is placed on the unwinding roller, and the brake on the unwinding roller maintains a certain tension of the paper web, and Quickly brake the paper roll when the head is broken. The paper web passes through the guiding roller to reach the slitting device, and several slitting circular cutters divide the paper into the required width, and then send it to the take-up roller for rewinding. After reaching the specified length, the paper is stopped and replaced with a new paper core. Repeat the above process. The main structural parameters of the winder are the width of the paper that can be processed and the maximum speed, followed by the maximum diameter of the paper and roll, the method of cutting and the length.
It can be seen from the working principle of the winder that the motor of the take-up roller drives the corresponding take-up roller to rotate the paper-wound paper core, the diameter of the paper roll gradually increases, and the axial center of the paper roll increases with the diameter. Gradually moving up, the platen roller moves up and gradually reduces the pressure. The unwinding motor mainly provides a reverse torque, creating tension on the paper surface, keeping the paper web flat, and the speed control of the unwinding motor is a process of gradually increasing speed, but the linear speed of the paper web remains unchanged.

Copper Tape Machine

Belt rewinding machine design and working principle ---

17
Measure the diameter of the exit roller.
The diameter measuring sensor or the super-sonic sensor is fixed on the floor in the middle of the paper exit. The sensor measures the diameter of the reel as the reel becomes smaller in the rack position.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com