Tear Tape Machine

Tear Tape Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department
1. Stretching device
The stretching device of the rewinder is set to keep the paper web slit after slitting. In some paper cutting knives, the stretcher is also used. The main function is to eliminate the texture and slack of the paper web. Mainly, it can maintain the good operation of slitting. There are three types of stretchers that we often use today: D-shaped stretches, curved rollers, and Z-type double-bar stretchers.
2, support roller
The backup roll is mainly used to support the paper roll, which is composed of a controlled cast iron roll or a general tube roll. The roller body is mainly cast iron pipe and steel pipe, and its diameter is usually 400-700 mm or more according to the width of the winder. The center-to-center ratio between the rolls of the backup roll should be greater than the roll diameter. Only at such a distance, the roll core does not get caught in the middle of the roll when the support roll begins to curl.
When the winder is running at high speed, in order to avoid vibration during high-speed operation, the design of the backup roller must be minimal when supporting the paper roll. The radius is a function expression of the speed and width of the winder, mainly by allowable The critical speed and the degree of winding are determined because at this time the diameter of the backup roll has less chance of producing a defect in the roll hardness than the small diameter support roll. When coiling coated paper or very thin paper, we should consider using a larger diameter backup roll. On a rewinder with a small width, we generally use a 600mm roll diameter.
 

Tear Tape Machine

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad

AC drives were quickly successful in paper mills in Europe and Japan. Most major drive manufacturers now offer AC drives for paper mills. Most domestic paper mills use ABB, Siemens and other company's complete rewinder AC drive systems. . For example, the 6SE7O series speed control device of Siemens Company has achieved the speed control performance and has exceeded or exceeded the DC speed regulation performance and become the preferred solution for the transmission. The domestic rewinding machine AC drive started in the middle and late C9 of the 20th century. Due to the lack of understanding and research of the AC drive system of the winder, few mature sets of equipment were introduced to the market.
At present, in the domestic paper industry, the drive control system of the winder is gradually developing from the all-digital DC drive control system to the AC variable frequency drive control system. With the continuous improvement of the production process and speed of the rewinding machine, the requirements for real-time control and monitoring of the rewinding machine production process are becoming higher and higher. In order to reduce the large amount of wiring between the rewinding machine production site and the control room, the signal is improved. The transmission speed and quality of the fieldbus and human-machine interface began in the late 1990s for rewinders. Fieldbus is a new type of control system for all-digital, two-way communication. Due to the intelligent and digitized fieldbus devices, it fundamentally improves the accuracy of measurement and control and reduces transmission errors compared with analog signals. At the same time, due to the simplified structure of the system, the equipment and wiring are reduced, the internal functions of the field instrument are strengthened, the round-trip transmission of signals is reduced, and the operational reliability of the system is improved. In addition, the field control equipment has the ability of self-diagnosis and simple fault handling, and sends related equipment operation information and diagnostic maintenance information to the man-machine interface through digital communication. The user can monitor the running status of all equipments, query the cause of the fault, and Process parameters (such as tension) are set and modified according to the different requirements of the rewinder process. For this reason, the application of fieldbus technology and HMI technology to the winder has become the development trend of automatic control of the winder. With the continuous promotion of inverter, HMI technology and fieldbus technology in the application of winder and the combination of computer technology and communication technology, the design speed of the winder can reach 300om/min, the working speed is 2500m/min, and the winder Many of the manual operations have been automated, and manual operations have been greatly reduced. The degree of automation and control accuracy, control speed and system stability will be raised to a new level.

Tear Tape Machine

Belt rewinding machine design and working principle ---

17
Measure the diameter of the exit roller.
The diameter measuring sensor or the super-sonic sensor is fixed on the floor in the middle of the paper exit. The sensor measures the diameter of the reel as the reel becomes smaller in the rack position.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com