Tape Braiding Machine

Tape Braiding Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department
1. Stretching device
The stretching device of the rewinder is set to keep the paper web slit after slitting. In some paper cutting knives, the stretcher is also used. The main function is to eliminate the texture and slack of the paper web. Mainly, it can maintain the good operation of slitting. There are three types of stretchers that we often use today: D-shaped stretches, curved rollers, and Z-type double-bar stretchers.
2, support roller
The backup roll is mainly used to support the paper roll, which is composed of a controlled cast iron roll or a general tube roll. The roller body is mainly cast iron pipe and steel pipe, and its diameter is usually 400-700 mm or more according to the width of the winder. The center-to-center ratio between the rolls of the backup roll should be greater than the roll diameter. Only at such a distance, the roll core does not get caught in the middle of the roll when the support roll begins to curl.
When the winder is running at high speed, in order to avoid vibration during high-speed operation, the design of the backup roller must be minimal when supporting the paper roll. The radius is a function expression of the speed and width of the winder, mainly by allowable The critical speed and the degree of winding are determined because at this time the diameter of the backup roll has less chance of producing a defect in the roll hardness than the small diameter support roll. When coiling coated paper or very thin paper, we should consider using a larger diameter backup roll. On a rewinder with a small width, we generally use a 600mm roll diameter.
 

Tape Braiding Machine

Design and application of constant tension and load distribution control for winder---

3 limitations of the original control system
This paper is aimed at the transformation of the rewinder analog DC drive system. The original rewinder control system mainly has the following shortcomings and limitations:
(1) The original rewinder control system is the DC drive control system of Siemens AG of Germany. Due to the DC motor drag, the analog regulator is adjusted, the device parameters are easy to drift, resulting in the reliability and accuracy of the rewinder, and Affect the quality and efficiency of rewinding, the maximum speed is only about 600m/min, it is difficult to meet the production requirements of high-speed paper machines.
(2) The original system uses mechanical buttons and instruments to operate and monitor the production process. The information integration capability is not strong. The process parameters of many production processes cannot be obtained, which increases the labor intensity of workers' operations and the time of manual participation in production, which affects the rewinding. Machine utilization and automation.
(3) The original system is a centralized system. A large number of I/O cables are distributed between the control room and the site, which not only increases the cost but also increases the system's unreliability.
(4) Due to incomplete information of field-level equipment, online fault diagnosis, alarm, and recording functions of field-level equipment are not strong. On the other hand, it is difficult to complete the parameterization functions such as remote parameter setting and modification of field devices, which affects the maintainability of the system.

Tape Braiding Machine

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com