Rewinder mechanical structure and control process ---
Second, the main structure of the winder
2.3 Rolling Department
1. Stretching device
The stretching device of the rewinder is set to keep the paper web slit after slitting. In some paper cutting knives, the stretcher is also used. The main function is to eliminate the texture and slack of the paper web. Mainly, it can maintain the good operation of slitting. There are three types of stretchers that we often use today: D-shaped stretches, curved rollers, and Z-type double-bar stretchers.
2, support roller
The backup roll is mainly used to support the paper roll, which is composed of a controlled cast iron roll or a general tube roll. The roller body is mainly cast iron pipe and steel pipe, and its diameter is usually 400-700 mm or more according to the width of the winder. The center-to-center ratio between the rolls of the backup roll should be greater than the roll diameter. Only at such a distance, the roll core does not get caught in the middle of the roll when the support roll begins to curl.
When the winder is running at high speed, in order to avoid vibration during high-speed operation, the design of the backup roller must be minimal when supporting the paper roll. The radius is a function expression of the speed and width of the winder, mainly by allowable The critical speed and the degree of winding are determined because at this time the diameter of the backup roll has less chance of producing a defect in the roll hardness than the small diameter support roll. When coiling coated paper or very thin paper, we should consider using a larger diameter backup roll. On a rewinder with a small width, we generally use a 600mm roll diameter.
Design and application of constant tension and load distribution control for winder---
4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.
Belt rewinding machine design and working principle ---
12Paper roll holder
When the paper roll is stopped, the paper roll is fixed at a certain position by the paper roll holder. The paper roll holder prevents slack and lateral movement of the paper roll. It is important to make a joint when making a customer roll. Roll holder on the take-up roll
The paper roll holder on the paper roll includes a spring-loaded plastic roll mounted on the paper cutter frame. When the paper cutter is in or on the middle position, the paper roll holder is placed against the surface of the rear bottom roller.
13 Automatic roll change
The rewinding device removes the paper roll from the winder.
The rewinding device cuts the sheet, pushes the paper roll onto the unloading station and fills in a new core for the rewinding.
The roll change can be started when the roll is decelerated. In the final stage of deceleration, the nipple guardrail and the platen roller rise to a high position. The unloader rises to the position where the paper roll is received. When the winder stops, the paper core clamp opens and rises to rise. The paper cutter is raised from between the paper rolls. The paper feed roller pushes the paper roll to the paper unloading station. At the same time, the paper cutter cuts the paper. The vacuum suction of the rear bottom roller sucks the cut sheet onto the roller. The core loader drops the new core onto the roll. The paper feed roller returns to its original position and the unloading table falls to the middle position. The paper core clip is lowered and closed. The platen roller and the nip guard are lowered. The winder crawls at a speed.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc