Rewinder mechanical structure and control process ---
Second, the main structure of the winder
2.3 Rolling Department
Nowadays, with the increase of the speed of the winder, most of the winders are equipped with unloaders, which are used to push the rolled paper rolls from the support rolls and unload them on the ground. It has many forms, the most common ones are the unwinding station and the unwinding pendulum. Its control mainly depends on air pressure or hydraulic pressure. The thief of the unwinder can be selected according to the number of operators, the size and quality of the core. The advanced foreign rewinding machine can automatically control the positioning of the mandrel and mandrel and the cutting of the paper, which can save auxiliary operation time and improve production efficiency.
4, transmission mechanism
The speed of the paper-feeding machine of the winder is generally about 15 to 40 m/min. In the process of raising the speed of the paper from low, we require the speed of the vehicle to rise, so that the paper roll can be avoided due to the fluctuation of the tension. The tightness is inconsistent. Uniform acceleration is required for breakage or shutdown. During the acceleration process, the average acceleration is usually 0.23~0.37m/s, and the acceleration time is usually 50~60s. In the braking process, the deceleration is 0.42~0.75m/s and the braking time is 40s. In order to meet the shifting requirements of the winder, most of the rewinding opportunities are driven by DC motors. In the previous rewinding system, a DC motor generally controlled two supporting rollers, and in the current rewinding machine, Development and research have started with two separate motor control rolls, which can control the speed difference between the two rolls, which is beneficial for taking up the appropriate tightness of the paper roll.
Belt rewinding machine design and working principle ---
rear bottom roller
The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.
Belt rewinding machine design and working principle ---
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc