Elastic Tape Making Machine

Elastic Tape Making Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.4 Pressure mechanism
1, the platen roller
First, in the rewinder system, the platen roller has a significant impact on the tightness control of the paper roll. Among them, the pressure adjusting mechanism plays a role of keeping the pressure of the paper roll and the supporting roll nip constant, and the main purpose is to prevent the paper roll from slipping or being wound too tight at the beginning of the work. The paper roll slips because the paper roll is too light, and the winding is too tight because the pressure is too high until the rewinding to the later stage. In the modern rewinder system, the platen roller is automatically controlled, so that the paper can be additionally applied. The force.
2. Hydraulic (air pressure) suspension mechanism
Under normal circumstances, the adjustable pressure actuators use hydraulic suspension scale mechanism. We install a potentiometer attached to the platen roller to display the diameter of the finished paper roll, which is sent through the potentiometer. The signal is transmitted to the pressure program control unit to calculate the pressure, so that the oil pressure in the suspension scale can be changed, thereby achieving pressure control of the platen roller.

Elastic Tape Making Machine

Belt rewinding machine design and working principle ---

2 rear bottom roller

The platen roller device consists of a combination of devices that can be combined. The platen roller is supported by bearings on the platen beam beam.
The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
working principle 
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.

Elastic Tape Making Machine

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com