Kinesiology Tape Making Machine

Kinesiology Tape Making Machine

Rewinder mechanical structure and control process ---

Third, the rewinding machine control performance indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
As the rewinder continuously performs rewinding, the diameter of the finished paper roll is gradually increased, and the weight of the finished paper roll is also gradually increasing, so that the contact points of the finished paper roll with the front and rear bottom rolls are also changing. So you can come to a conclusion like this:
If the pressure of the platen roller is kept constant and does not change, the pressure between the contact points of the finished paper roll and the front and rear bottom rolls is not guaranteed to be constant, and the change in the contact point causes the pressure generated between them to change accordingly. Therefore, if we want the paper roll to reach the best form, we must adjust the pressure exerted by the platen roller to compensate for the influence of the above two factors. Only in this way can the pressure between the front and rear bottom rollers and the finished paper roll be guaranteed. Variety.
2, support roller torque program control In the rewinding process of the finished paper roll, in order to obtain high quality finished paper roll, the speed control or the support roller torque should meet certain conditions, if the speed control is used, the support roller The speed between the two should be less than 0.2%. As the diameter of the paper roll increases, the speed of the two supporting rollers must be close. Only in this way can the high quality finished paper roll be rewinded, but some quick checking systems cannot consider this design. 

Kinesiology Tape Making Machine

Belt rewinding machine design and working principle ---

2 rear bottom roller

The platen roller device consists of a combination of devices that can be combined. The platen roller is supported by bearings on the platen beam beam.
The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
working principle 
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.

Kinesiology Tape Making Machine

Belt rewinding machine design and working principle ---

 

9 small paper rolls launched
The small paper roll ejecting device is used for those paper rolls that are too small for the paper feed roller. The small paper roll ejecting device is mounted on the paper feed roller. It relies on hydraulic pressure to move. The minimum diameter that the small paper roll exit can be pushed out is 200 mm (7.9 in).


10 paper cutter construction
The paper cutter is a zigzag blade, which cuts the slit webs during roll ejection. The paper cutter rises from the paper roll to the paper cutting position. The movement of the paper cutter is done by a lever driven by a hydraulic cylinder.
working principle 
The paper roll is pressed against the raised paper cutting blade by the ejector pin and cut.


11 core positioning pin
The end of the core loader is a paper core locating pin attached to the rewinder frame. The paper core positioning pin includes a metal plate and a frame. The scale on the core locating pin shows the position of the locating pin. The paper core locating pin holds the paper core in the correct position on the core loader only by the edge of the slitter. The core positioning pin is placed in close proximity to the slit and is locked in that position by the locking arm.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com