Aluminum Foil Tape Machine

Aluminum Foil Tape Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

Part 1: Mechanical parts
The mechanical part mainly consists of a paper exiting section, a paper cutting section, a double curved roller section, a paper winding section, and an automatic paper guiding section.
1. Ejection department:
The structure is all welded by steel plate, equipped with an empty paper roll temporary storage guide rail. The paper-removing roller is locked on the paper-removing frame by the hydraulic operating lever. After the paper is finished, the paper-returning core is pushed onto the guide rail to replace the paper. Roll and start-up operation saves time. A bumper is attached to the end of the exit frame rail to reduce vibration and noise caused by the roll change.
The coupling clutch is located between the paper roller and the brake motor, hydraulically operated, and is interlocked with the hook safety anti-lift device. The crane hook cannot lift the empty paper return shaft before the roll paper completes the clutch has been disengaged. Security performance.
With brake generator drive and hydraulic control, the paper return frame is horizontally adjusted by hydraulic motor and has a lateral swing function with a maximum swing of ±50mm. The emergency brake uses a brake generator and a hydraulic disc brake. The brake is imported from abroad, with small volume, large braking torque and good reliability.

 

Aluminum Foil Tape Machine

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

Aluminum Foil Tape Machine

Belt rewinding machine design and working principle ---

14 change roll
The roll change blower is used to blow the cut sheet onto the core. On the platen roller, there are three blowing tubes on the paper core with a blowing tube under the paper core. When blasting is used, the paper will bypass the core at the beginning of the machine.


15 paper cut hair dryer
The web cut blower is used when the web must be cut quickly. The blow tube is located between the guide rollers.
The blow tube is activated by a safety photocell or a manually transmitted pulse signal.
1- Spreading roller
2- Adjust the paper wrap angle device,
3- Stretch roller bending direction adjustment device
A- paper web
B- First stretch roll bending direction
C- second stretch roll bending direction
Stretching device
The stretching device on the illustration is the basic position of the display. The web A passes directly through the spreader roll, which means that the web curvature is zero. The first spreader roll B is at an angle of 90 degrees with respect to the sheet. The second spreader roll has a camber at the base position when the cylinder pressure is 0 bar. The cylinder pressure can be read on the meter at the location of the control system.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com