Seal Machine Portable Tape

Seal Machine Portable Tape

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

Part 1: Mechanical parts
The mechanical part mainly consists of a paper exiting section, a paper cutting section, a double curved roller section, a paper winding section, and an automatic paper guiding section.
1. Ejection department:
The structure is all welded by steel plate, equipped with an empty paper roll temporary storage guide rail. The paper-removing roller is locked on the paper-removing frame by the hydraulic operating lever. After the paper is finished, the paper-returning core is pushed onto the guide rail to replace the paper. Roll and start-up operation saves time. A bumper is attached to the end of the exit frame rail to reduce vibration and noise caused by the roll change.
The coupling clutch is located between the paper roller and the brake motor, hydraulically operated, and is interlocked with the hook safety anti-lift device. The crane hook cannot lift the empty paper return shaft before the roll paper completes the clutch has been disengaged. Security performance.
With brake generator drive and hydraulic control, the paper return frame is horizontally adjusted by hydraulic motor and has a lateral swing function with a maximum swing of ±50mm. The emergency brake uses a brake generator and a hydraulic disc brake. The brake is imported from abroad, with small volume, large braking torque and good reliability.

 

Seal Machine Portable Tape

Belt rewinding machine design and working principle ---

5:Unloading table action
1- Unloading table rise position
2- Middle position of the unloader
The unloading station transfers the paper roll from the winder to the ground.
Construction
The unloader is a device mounted on the floor to remove the paper roll. The platform is controlled by a hydraulic cylinder. The platform is a steel structure. The platform hydraulic unit is equipped with a load relief valve. These are to ensure the control process of the unloading roll.
working principle 
When the paper roll is advanced onto the platform in the upper position, the platform unloads the paper roll to the intermediate position and then onto the floor, and the paper roll rolls off the platform. For safety reasons, the platform will not automatically unload paper onto the floor unless it is moved by the operator from the intermediate position to the unloading position. The reel cannot be unloaded to the floor anyway before the new rewind.

Seal Machine Portable Tape

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com