Tape Binding Sewing Machine

Tape Binding Sewing Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
      Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
      The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.

Tape Binding Sewing Machine

Belt rewinding machine design and working principle ---

5:Unloading table action
1- Unloading table rise position
2- Middle position of the unloader
The unloading station transfers the paper roll from the winder to the ground.
Construction
The unloader is a device mounted on the floor to remove the paper roll. The platform is controlled by a hydraulic cylinder. The platform is a steel structure. The platform hydraulic unit is equipped with a load relief valve. These are to ensure the control process of the unloading roll.
working principle 
When the paper roll is advanced onto the platform in the upper position, the platform unloads the paper roll to the intermediate position and then onto the floor, and the paper roll rolls off the platform. For safety reasons, the platform will not automatically unload paper onto the floor unless it is moved by the operator from the intermediate position to the unloading position. The reel cannot be unloaded to the floor anyway before the new rewind.

Tape Binding Sewing Machine

Belt rewinding machine design and working principle ---

14 change roll
The roll change blower is used to blow the cut sheet onto the core. On the platen roller, there are three blowing tubes on the paper core with a blowing tube under the paper core. When blasting is used, the paper will bypass the core at the beginning of the machine.


15 paper cut hair dryer
The web cut blower is used when the web must be cut quickly. The blow tube is located between the guide rollers.
The blow tube is activated by a safety photocell or a manually transmitted pulse signal.
1- Spreading roller
2- Adjust the paper wrap angle device,
3- Stretch roller bending direction adjustment device
A- paper web
B- First stretch roll bending direction
C- second stretch roll bending direction
Stretching device
The stretching device on the illustration is the basic position of the display. The web A passes directly through the spreader roll, which means that the web curvature is zero. The first spreader roll B is at an angle of 90 degrees with respect to the sheet. The second spreader roll has a camber at the base position when the cylinder pressure is 0 bar. The cylinder pressure can be read on the meter at the location of the control system.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com