Bopp Tape Roll Slitter

Bopp Tape Roll Slitter

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Bopp Tape Roll Slitter

Slip axis and air shaft of slitting machine--

 

Sliding gas rising shaft structure characteristics and principle: Slip type gas rising shaft mainly consists of mandrel, airbag, slip sleeve and other parts.
Air enters the inside of the air bag to cause air expansion, pushes each torque group to expand outward, and sets the slip torque value of each torque group according to the inflation pressure, which is convenient for controlling the tension adjustment of each roll of material on the slitter. .
The slip type air rising shaft is mainly used for the striping equipment with high quality requirements and fast speed.
Slip-type air-up shaft technical parameters: slip-type air-up shaft main body outer diameter Φ75mm, action outer diameter Φ78mm, suitable for paper tube Φ76±0.2mm.

Bopp Tape Roll Slitter

Slitting machine operation guide ---

3 job responsibilities
3.1 Slicing machine gear duties
3.1.1 Conscientiously abide by the rules and regulations of the company and the production department, and obey the leadership with the monitor.
3.1.2 Proper operation and use of equipment, strict compliance with safe operating procedures, and timely elimination of common faults.
3.1.3 According to the requirements of product quality standards, it is responsible for the quality, consumption, safety and task completion of the machine, and self-inspection and its records.
3.1.4 Responsible for guiding, supervising and managing the work of the machine personnel.
3.1.5 According to the maintenance requirements of the equipment, carefully carry out the maintenance work of the equipment.
3.1.6 Work with the machine personnel to do a good job of cleaning the equipment and the area of ??responsibility.
3.1.7 Carefully carry out the work of handover, and communicate and record the problems existing in the operation of the equipment.
3.1.8 Have the responsibility for care and maintenance of the auxiliary facilities (lighting, emergency lights, tables, chairs, shelves, etc.) belonging to the machine and surrounding.
3.1.9 Complete the other tasks assigned to the squad leader and the superior leader.
3.2 Slitting machine auxiliary duties
3.2.1 Conscientiously abide by the rules and regulations of the company and the production department, obey the management of the vehicle, and strictly abide by the safe operating procedures.
3.2.2 Carefully assist the gear shifter to adjust and troubleshoot the equipment, and timely carry out the sanitary cleaning work within the scope of the equipment responsibility area under its jurisdiction.
3.2.3 Do a good job in preparation before starting the machine, do a good job in paper and product handling, and do a good job in quality self-inspection.
3.2.4 Clean up waste paper, garbage, packaging materials and evacuate the production site in time; cut off the power and air supply of the machine and auxiliary facilities at the end of the work.
3.2.5 Receive raw and auxiliary materials according to the requirements of the gears and do the work and identification of the original and auxiliary materials.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com