Production Of Masking Machine

Production Of Masking Machine

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Production Of Masking Machine

Domestic cutting machine development status and outlets ---

1. Not rigorous in the manufacturing process
Tolerance control in the mechanical manufacturing process is not precise enough, and the surface is rough, especially in the matching electroplating industry, which is shoddy. There is a defect in the dynamic balance of the roller for cutting the Chinese-made equipment at one time. The lag of the related industry, the rubber coated by the roller has far less wear resistance and anti-aging than the foreign products. The bearings used seem to use well-known foreign brands, but the counterfeit and shoddy floods the domestic bearing market. Even when the real goods are purchased, the precision is far lower than the precision used by foreign slitting machines.
In the entire production process of a slitting machine, there is no guarantee of production process. At present, most of the slitting machines produced in China are completed by a number of outsourcing units, and the quality of their production is even more difficult to guarantee. In addition, the metal materials used and the heat treatment process are not rigorous enough, resulting in many problems in the use of a slitting machine. It has seriously affected the share of a slitting machine in the domestic market. The secondary and tertiary slitting machines have fewer problems than the one slitting machine, because the parts of the secondary and tertiary slitting machines are completed by the slitting machine manufacturer, and the dynamic balancing machine used is in a narrow range. It can accurately control the unbalanced grams, and the industrial difficulty coefficient of manufacturing is reduced. Its selling price is far lower than that of foreign products. Therefore, the proportion of domestically produced slitting machines in the domestic slitting machine market getting bigger.

Production Of Masking Machine

Domestic cutting machine development status and outlets ---

3. Lack of insight into the characteristics of different materials at the time of slitting, distinguishing between control systems and structures
Everyone knows that the physical properties of different materials are inconsistent. Some materials are smooth and firm. Some materials are very soft and soft, and the physical properties of the same material with different thicknesses are not the same. Among the slitting machines, the structure is also different, and there is a lack of changes in the control system due to its structural changes. The difference is rarely studied. In particular, the change in the difference in the control curve is even less known, and its mature control system software is still very few in China. Although some people have tried the application of a slitter control software, the chances of success are very low. Most of them are characterized by “headaches and pains.” Although our company has experienced 7-8 years of hard work, Some experience has been gained and the control system is becoming more mature, but there is still a certain gap compared with the materials covered by well-known foreign brands.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com