Cellotape Tape Making Machine

Cellotape Tape Making Machine

Preparation of slitter cutter
1. Razor slitting
1.1. The razor slitting requires the film to travel in the correct direction to the winding section.
1.2. Adjust the photoelectric tracking to bring the film to the proper position.
1.3. Tension the film and attach the blade to the razor holder.
1.4. According to the specifications required by the instruction sheet, the sliding razor holder is cut into the razor groove under the film, and the blade edge and the edge of the sipe are required to be in contact with each other.
1.5 After adjusting the depth of the cutter, lock the razor frame screws.
2. Round knife cutting
2.1. Check whether the upper and lower knives are sharp and have no gaps, and vice versa;
2.2. Determine the number of knives (N+1) according to the number of product series (N);
2.3. Install the lower knife to adjust the width of the lower knife according to the actual width of the product;
2.4 Install the upper knife correctly. The flat side of the upper knife is aligned with the side of the lower cutting edge. The upper knife is aligned with the gap between the lower knife and the septum. Press the screws on both sides to make the upper knife enter the gap depth to about 2mm. The upper knife is attached to the lower knife and fastened. Finally, the screw on the left side of the upper knife holder is adjusted so that the whole knife holder moves 1-2 mm to the right side and is fastened.

Cellotape Tape Making Machine

Domestic cutting machine development status and outlets ---

three. Domestic slitting machine development direction
The development direction of domestic slitting machines should be considered from three aspects:

3. Manufacturing: This is a common problem faced by China's manufacturing industry. Everyone knows that any mechanical equipment, besides being reasonable in design, requires precision in manufacturing, and Chinese manufacturing is lacking in this respect. The manufacturing process is also a weak link. In addition to some general-purpose machine tools, there are some special equipments for manufacturing slitting machines, such as dynamic balancing machines, water cutting machines, etc., due to the manufacturing precision requirements of the slitting machine. High, therefore, some equipment needs to use CNC machine tools to process parts, especially the need to popularize the machining center, so that the processing precision of the equipment that produces the slitting machine can be fundamentally guaranteed.

Cellotape Tape Making Machine

Slitting machine parts ---

 

2. Attenuation and tension compensation of the tension of the rewinding and unwinding: It is generally believed that maintaining the constant tension of the aluminum foil during the rewinding and unwinding of the aluminum foil is beneficial to the apparent quality of the finished aluminum foil, but it is not. The best method is to increase the tension of the aluminum foil according to a certain rule as the diameter of the coil increases, and the smaller the diameter, the lower the tension value. There are automatic tension control and manual tension control during the slitting operation. The automatic tension control system is the leading set tension attenuation value, which is maintained throughout the winding process. The manual tension control requires the operator to continuously adjust the diameter of the master roll to meet the tension required for the aluminum foil during operation. When setting the automatic tension operation, set the initial tension before setting the tension attenuation value. Taking the setting of the slitting and unwinding attenuation value as an example, the setting principle is that the aluminum foil tension attenuation value (%) is equal to the tension at the end of winding of the aluminum foil minus the initial tension and then divided by the initial tension. Multiply by 100%. When setting the automatic tension value of the unwinding, it should not be too large, otherwise the aluminum foil winding surface has a large hardness and is prone to warping. But the tension should not be too small, too small and easy to cause the rewinding body to be too loose, and the winding is not neatly running. Therefore, the quality of the rewinding and unwinding during the aluminum foil slitting operation is mainly affected by the change of the tension of the aluminum foil. It can be seen that the mastery of the retracting and unwinding control system is the key to affecting the quality.

3. The change of speed during slitting affects the change of tension: When the speed is increased or decelerated, the speed of the main motor changes. Firstly, it causes the instantaneous change of the tension of the unwinding traction to the winding section of the aluminum foil, and it is necessary to slightly vibrate the aluminum foil after a period of time to gradually stabilize the tension. The instability of this tension is manifested in the fact that the finished roll is not well-wound, and the end face has unevenness, which affects the quality of the product.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com