Adhesive Tape Slittig Machine

Adhesive Tape Slittig Machine

Slitting machine starts production
1. The winding roller is pressed down, the counter is cleared, and the production is started;
2. During the operation process, check the winding status of each joint from time to time, and adjust the tension according to the tightness of the winding to make each volume
The material is wound up and the end face is flush and firm;
3. Always pay attention to product quality during machine operation.
4. The machine has no abnormal sound.
5. Whether the photoelectric tracking operation is normal.
6. When checking the next volume, pay attention to check the surface of the product for quality defects and stick the tape as required.

Adhesive Tape Slittig Machine

Slitting machine operation guide ---

6 Safety Precautions
6.1 The operator must be trained to work and wear the labor protection products correctly; carefully check the protective devices, safety interlocks, test buttons, emergency buttons, etc. of the machine before starting the machine, and confirm that the machine can be turned on after normal operation.
6.2 The slitting machine is a double-operated equipment. It is forbidden to operate in tandem, especially when the equipment is repaired.
6.3 The cut products should be stacked neatly and securely, and fixed with a cannula to prevent the product from slipping and hurting people.
6.4 When working, it is not allowed to place any irrelevant items such as oil pots and tools on the workbench.
6.5 During the operation of the machine, it is strictly forbidden to reach into the circumference of the slitting knife or the pressure roller. Even if the vehicle has been stopped but the power is not disconnected, it is forbidden to perform the tool change, paper adjustment and adjustment under the knife.
6.6 Slitting blades must be protected during handling and storage, and must not be handled or stored with bare edges.
6.7 The interlocking protection devices of all parts of the equipment shall not be short-circuited or removed, and if malfunction or abnormality occurs, stop immediately and report to the machine for repair and maintenance.
6.8 Machine personnel shall not perform fault repair or equipment adjustment of fault type, and the power distribution cabinet, switch box, etc. shall not be opened without authorization, and shall not store items.
6.9 When handing over the shift, you must hand over the site, and you must explain the production and equipment operation of the class to the next one.
6.10 Check the surrounding conditions before leaving work, and cut off the power and air supply of the machine and related equipment.

Adhesive Tape Slittig Machine

Domestic cutting machine development status and outlets ---

1. Not rigorous in the manufacturing process
Tolerance control in the mechanical manufacturing process is not precise enough, and the surface is rough, especially in the matching electroplating industry, which is shoddy. There is a defect in the dynamic balance of the roller for cutting the Chinese-made equipment at one time. The lag of the related industry, the rubber coated by the roller has far less wear resistance and anti-aging than the foreign products. The bearings used seem to use well-known foreign brands, but the counterfeit and shoddy floods the domestic bearing market. Even when the real goods are purchased, the precision is far lower than the precision used by foreign slitting machines.
In the entire production process of a slitting machine, there is no guarantee of production process. At present, most of the slitting machines produced in China are completed by a number of outsourcing units, and the quality of their production is even more difficult to guarantee. In addition, the metal materials used and the heat treatment process are not rigorous enough, resulting in many problems in the use of a slitting machine. It has seriously affected the share of a slitting machine in the domestic market. The secondary and tertiary slitting machines have fewer problems than the one slitting machine, because the parts of the secondary and tertiary slitting machines are completed by the slitting machine manufacturer, and the dynamic balancing machine used is in a narrow range. It can accurately control the unbalanced grams, and the industrial difficulty coefficient of manufacturing is reduced. Its selling price is far lower than that of foreign products. Therefore, the proportion of domestically produced slitting machines in the domestic slitting machine market getting bigger.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com