Tape slitter setting control：
1. Set the slitting menu according to the type, thickness, length, width, etc. of the film arranged in the slitting plan.
2. Lift the corresponding BOPP film file from the PDF.
3. Set the winding length and width of the film of the corresponding specification.
4. Select the corresponding winding station, adjust the pressure roller arm and pressure roller, and install the paper core of the corresponding specifications.
Reasons, countermeasures and effects of BOPP film slitting quality ---
twelve. Interface quality problem (poor interface quality, interface identifier does not match)
2. Interface identifier
Due to the large thickness of the film interface, the film roll for some applications must be properly handled at the interface to avoid unnecessary problems, such as slowing down, increasing the gap between the coating blade, and printing the offset plate. The interface products must be identified as necessary to facilitate customer identification and internal management.
1 The color of the adhesive interface is generally beige, special requirements are used according to the regulations. For example, Shanghai Ziquan requires the use of black adhesive tape; the marking method of the joint position is operated according to the regulations, such as Zhuhai Zhongfu Pearl Film, Shenzhen Ruimei The hot film is required to be marked at the ends of the interface with yellow paper dust protruding from the end of the film roll by about 1 cm; other special marks are operated according to the requirements of the production tribe.
2 Require the slitting workshop to mark the length number of the joint product without special requirements after the length of the label in the length column of the package label, and mark the “buter” mark on the note bar of the computer, and mark “+” on the remark column. Marking, pearl film and imitation paper film and exporting pearl film should indicate the length of each product before and after the joint on the length column of the product specification. For special requirements, the relevant marking work should be done according to the regulations (such as Shanghai Ziquan product port). The rate of less than or greater than 25% requires the number of interface products on each board product).
Slitting machine operation guide ---
3 job responsibilities
3.1 Slicing machine gear duties
3.1.1 Conscientiously abide by the rules and regulations of the company and the production department, and obey the leadership with the monitor.
3.1.2 Proper operation and use of equipment, strict compliance with safe operating procedures, and timely elimination of common faults.
3.1.3 According to the requirements of product quality standards, it is responsible for the quality, consumption, safety and task completion of the machine, and self-inspection and its records.
3.1.4 Responsible for guiding, supervising and managing the work of the machine personnel.
3.1.5 According to the maintenance requirements of the equipment, carefully carry out the maintenance work of the equipment.
3.1.6 Work with the machine personnel to do a good job of cleaning the equipment and the area of ??responsibility.
3.1.7 Carefully carry out the work of handover, and communicate and record the problems existing in the operation of the equipment.
3.1.8 Have the responsibility for care and maintenance of the auxiliary facilities (lighting, emergency lights, tables, chairs, shelves, etc.) belonging to the machine and surrounding.
3.1.9 Complete the other tasks assigned to the squad leader and the superior leader.
3.2 Slitting machine auxiliary duties
3.2.1 Conscientiously abide by the rules and regulations of the company and the production department, obey the management of the vehicle, and strictly abide by the safe operating procedures.
3.2.2 Carefully assist the gear shifter to adjust and troubleshoot the equipment, and timely carry out the sanitary cleaning work within the scope of the equipment responsibility area under its jurisdiction.
3.2.3 Do a good job in preparation before starting the machine, do a good job in paper and product handling, and do a good job in quality self-inspection.
3.2.4 Clean up waste paper, garbage, packaging materials and evacuate the production site in time; cut off the power and air supply of the machine and auxiliary facilities at the end of the work.
3.2.5 Receive raw and auxiliary materials according to the requirements of the gears and do the work and identification of the original and auxiliary materials.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc