Opp Jumbo Roll Slitter Rewinder Machine

Opp Jumbo Roll Slitter Rewinder Machine

Tape slitting machine feeding, filming and filming
1. Loading: According to the requirements of the cutting plan, according to the driving operation rules, according to the actual situation, hoist the corresponding mother roll on the aging frame, place it on the unwinding unwinding frame according to the inner and outer selection direction of the corona surface, and use the control button Clamp the steel core, leave the steel core support arm and drive.
2. Film penetration: When there is no film on the slitter, the film must be penetrated. Using the slitting machine through the membrane device and the function keys, one end of the original membrane is attached to the membrane chain eyelet, and the membrane button is activated to distribute the membrane along the slitting process to be evenly distributed on each roller.
3. Film: When there is a film on the slitter, when changing the joint, use the vacuum filming table to start the filming station to the working position, manually flatten the film on the first pulling roller of the slitting machine and start the upper vacuum pumping film. Soak the film flat on the filming table, attach the double-sided tape and cut off the excess film under the tape, flatten the film on the unwinding frame and start the lower vacuum pump to make the film flat and absorb the paper. Layer and flatten the adhesive film, the joints should be neat and wrinkle-free, then turn off the upper and lower vacuum pumps to open the filming station to the inoperative position.

Opp Jumbo Roll Slitter Rewinder Machine

Slitting machine operation guide ---

6 Safety Precautions
6.1 The operator must be trained to work and wear the labor protection products correctly; carefully check the protective devices, safety interlocks, test buttons, emergency buttons, etc. of the machine before starting the machine, and confirm that the machine can be turned on after normal operation.
6.2 The slitting machine is a double-operated equipment. It is forbidden to operate in tandem, especially when the equipment is repaired.
6.3 The cut products should be stacked neatly and securely, and fixed with a cannula to prevent the product from slipping and hurting people.
6.4 When working, it is not allowed to place any irrelevant items such as oil pots and tools on the workbench.
6.5 During the operation of the machine, it is strictly forbidden to reach into the circumference of the slitting knife or the pressure roller. Even if the vehicle has been stopped but the power is not disconnected, it is forbidden to perform the tool change, paper adjustment and adjustment under the knife.
6.6 Slitting blades must be protected during handling and storage, and must not be handled or stored with bare edges.
6.7 The interlocking protection devices of all parts of the equipment shall not be short-circuited or removed, and if malfunction or abnormality occurs, stop immediately and report to the machine for repair and maintenance.
6.8 Machine personnel shall not perform fault repair or equipment adjustment of fault type, and the power distribution cabinet, switch box, etc. shall not be opened without authorization, and shall not store items.
6.9 When handing over the shift, you must hand over the site, and you must explain the production and equipment operation of the class to the next one.
6.10 Check the surrounding conditions before leaving work, and cut off the power and air supply of the machine and related equipment.

Opp Jumbo Roll Slitter Rewinder Machine

Domestic cutting machine development status and outlets ---

2. Lack of composite professional talents who understand manufacturing technology and process and know cutting process
In the manufacturing process of the slitting machine, different customers are often faced with different materials and requirements. If different manufacturers produce the same materials, the raw materials used are not the same chemical plant products, and the physical properties of the materials produced are not the same. When producing the slitting machine, it cannot be generalized. In the production process, the manufacturing process will change, especially in the size of the roll diameter and the thickness of the coating layer, the difference between the active roller and the passive roller and the wrap angle of the roller surface, etc. The lack of corresponding research talents in the field often leads to many waste products and defective products in the slitting process. Such composite talents should not only be familiar with the design and manufacturing process of the entire slitting machine, but also understand the different characteristics of different materials during slitting. Currently, it is very scarce in China, which leads to the current situation of domestic slitting machines.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com