Sellotape Slitting Machine

Sellotape Slitting Machine

Tape slitter starts up
1. Change the specification, the paper core is on the inner and outer winding arms, and the pressure roller is in the ready state to notify all personnel to leave the machine and prepare to run.
2. Put the ANTI-STAIC BARS on the main console into AUTO, READY TO RUN is turned on, and start MACHINE RUN to start up.

Tape cutting machine cutting control
During the slitting operation process, carefully observe and observe the effect of cutting and cutting, and appropriately adjust and control the slitting speed, unwinding tension, contact pressure, curved roller, edge pulling roller and leading edge.

Sellotape Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)

2. Interface identifier
Due to the large thickness of the film interface, the film roll for some applications must be properly handled at the interface to avoid unnecessary problems, such as slowing down, increasing the gap between the coating blade, and printing the offset plate. The interface products must be identified as necessary to facilitate customer identification and internal management.
1 The color of the adhesive interface is generally beige, special requirements are used according to the regulations. For example, Shanghai Ziquan requires the use of black adhesive tape; the marking method of the joint position is operated according to the regulations, such as Zhuhai Zhongfu Pearl Film, Shenzhen Ruimei The hot film is required to be marked at the ends of the interface with yellow paper dust protruding from the end of the film roll by about 1 cm; other special marks are operated according to the requirements of the production tribe.
2 Require the slitting workshop to mark the length number of the joint product without special requirements after the length of the label in the length column of the package label, and mark the “buter” mark on the note bar of the computer, and mark “+” on the remark column. Marking, pearl film and imitation paper film and exporting pearl film should indicate the length of each product before and after the joint on the length column of the product specification. For special requirements, the relevant marking work should be done according to the regulations (such as Shanghai Ziquan product port). The rate of less than or greater than 25% requires the number of interface products on each board product).

Sellotape Slitting Machine

Slitting machine operation guide ---

6 Safety Precautions
6.1 The operator must be trained to work and wear the labor protection products correctly; carefully check the protective devices, safety interlocks, test buttons, emergency buttons, etc. of the machine before starting the machine, and confirm that the machine can be turned on after normal operation.
6.2 The slitting machine is a double-operated equipment. It is forbidden to operate in tandem, especially when the equipment is repaired.
6.3 The cut products should be stacked neatly and securely, and fixed with a cannula to prevent the product from slipping and hurting people.
6.4 When working, it is not allowed to place any irrelevant items such as oil pots and tools on the workbench.
6.5 During the operation of the machine, it is strictly forbidden to reach into the circumference of the slitting knife or the pressure roller. Even if the vehicle has been stopped but the power is not disconnected, it is forbidden to perform the tool change, paper adjustment and adjustment under the knife.
6.6 Slitting blades must be protected during handling and storage, and must not be handled or stored with bare edges.
6.7 The interlocking protection devices of all parts of the equipment shall not be short-circuited or removed, and if malfunction or abnormality occurs, stop immediately and report to the machine for repair and maintenance.
6.8 Machine personnel shall not perform fault repair or equipment adjustment of fault type, and the power distribution cabinet, switch box, etc. shall not be opened without authorization, and shall not store items.
6.9 When handing over the shift, you must hand over the site, and you must explain the production and equipment operation of the class to the next one.
6.10 Check the surrounding conditions before leaving work, and cut off the power and air supply of the machine and related equipment.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com