Printing Tape Slitting Machine

Printing Tape Slitting Machine

Main factors affecting tension stability:
(1) The change of the speed of the machine will inevitably cause the change of the tension of the whole machine.
(2) During the process of collecting and unwinding, the winding and unwinding diameters of the slitting machine are constantly changing, and the change of the diameter will inevitably cause the change of the material tension. When the unwinding torque is constant, the diameter is reduced and the tension is increased. The winding is reversed. If the winding torque is constant, the tension will decrease as the winding diameter increases. This is the main factor that causes the change in material tension during operation.
(3) The change in the tightness of the raw material roll will also cause a change in the tension of the whole machine.
(4) The unevenness of the material of the raw material is cut. If the material elasticity fluctuates, the material thickness changes along the width and length direction, the mass of the material roll is eccentric, and the temperature and humidity of the production environment change, which also affects the tension fluctuation of the whole machine.
(5) The various transmission mechanisms (such as guide rollers, floating rollers, flattening rollers, etc.) of the slitting machine have factors such as imbalance and unstable air pressure.

Printing Tape Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

(iv) Effect of film roll tightness on product quality

(5) Coping methods
1. Reasonable principle: Applicable is reasonable, which means that the cutting operator and the quality inspector are too loose according to the winding/
Too tightly influence the degree of influence on different products, adjust the cutting process reasonably, and reasonably grasp the tightness of the film roll to meet the requirements of the use of film products.
2. Ningsong Motight principle: objective when cutting equipment status, product specifications, film performance characteristics, etc.
When the influence of the condition causes the winding tightness to be in an inappropriate degree, the principle of tightness is generally used, because the problem of over-tightening often makes the film unusable, except for the special requirements.
3. The principle of primary and secondary: it means that in the process of slitting production, small groups should be followed to the interests of large collectives.
The principle of benefiting the interests of the company, avoiding the pursuit of high output and high distribution for the purpose of reducing the quality of cutting, all should be based on product quality, maintaining the German crown film brand as the responsibility, effectively completing various production and quality indicators Effectively serve the enterprise and users, and strive to be the best supplier of film.
4. System Management Principles: Refers to the use of systematic, scientific management methods, practical, theoretical, and empirical
The accumulated cutting control method is compiled, and according to the optimal combination of different types of products, width, winding length, season and other external variables and slitting tension, pressure and other internal variables, the document control management is performed to form an operation guidance document. Minimize the influence of subjective factors, reduce the impact caused by insufficient individual ability or excessive dependence on experience, and continuously supplement, optimize and improve the operation guidance documents to meet the needs of system management.

Printing Tape Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

Seven. Sharp edge
The curling occurs at the edge of the film winding, which causes the curling. The reason is that the edge of the thick film is curled up and the edge part is lifted up; the second is that the winding is too tight, and the tension can be shortened by slitting. Speed ??to improve the resulting edge curling phenomenon; third, the cutter is too blunt, and the stretching phenomenon occurs at the slit when slitting, causing the edge of the film roll to be turned outwards after winding to cause the curling edge, and the cutting should be replaced in time. The knife can avoid the occurrence of the curling problem; the fourth is that the tool is not installed correctly, such as the blade is close to the edge of the sipe and the blade is passivated. Cutting with a round knife can improve the curling of the film roll.
In the use of the unwinding process, there will be different degrees of side-floating in the unwinding process, and it is impossible to track the alignment with the electric eye, which directly affects the use effect. Therefore, it is necessary to change the product with the curled edge.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com