Super Clear Tape Slitting Machine

Super Clear Tape Slitting Machine

Tension information detection method
(1) Tension sensor detection method: It is a method of detecting the tension directly, closely combined with the machine, and without moving parts. Usually two sensors are paired and mounted on the end shafts on both sides of the detection guide roller.
(2) Roll diameter calculation type detection method: It uses the proximity switch installed at the reel to detect the rotation speed of the reel. Because the reel rotates once, the winding diameter will change twice the thickness of the material.
The current diameter of the reel is obtained by cumulative calculation by the initial value of the reel diameter and the material thickness, and the change of the corresponding reel diameter reflects the change of the actual tension value.
(3) Floating roller position detection mode: It uses the cylinder attached to the slitter to connect the floating roller to drive the angular displacement sensor to detect the tension change. When the tension is stable, the tension on the material is balanced with the cylinder force, so that the floating roller is in the center position. When the tension changes, the balance between the tension and the cylinder force is broken, and the position of the floating roller will rise or fall. At this time, the swing lever will rotate around a point and drive the floating roller angular displacement sensor to rotate together.
(4) Floating roller position + tension sensor combined tension detection mode: It can simultaneously detect the floating roller position signal output by the floating roller angular displacement sensor and the tension signal output by the tension sensor, thereby providing higher precision tension control to the system. [3].

Super Clear Tape Slitting Machine

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

two. Wrinkle (wrinkle, vertical wrinkle, cross wrinkle, line wrinkle)

Through many years, the BOPP industry has carried out a series of intensive and meticulous work on solving the problem of wrinkling. From the two aspects of process parameter screening and equipment adjustment and transformation, we have found a set of effective solutions and received very good results. effect,
Methods include:

5 Under the same parameters, the long gauge is more likely to wrinkle than the short gauge film roll, which means that the longer the specification, the worse the exhaust effect, and the lower the strength of the long gauge paper tube, the slitting process paper The slight bending of the tube tends to cause the film in the middle of the film roll to wrinkle for a long time, and when the paper core is long, under the high-speed rotation of the slit, as the axis of the film winding, its straightness, concentricity, strength, The indicators such as surface finish are the most important. Generally speaking, the longer the paper core, the more difficult it is to ensure the straightness and concentricity. Therefore, the quality of the paper core is very important. It is necessary to improve the inspection of the paper core. If the paper tube is found during the slitting process, the paper tube is found. The quality is abnormal and needs to be replaced in time. In addition, under the same parameter conditions, the short gauge is more prone to deviation than the long gauge membrane coil, and a large winding pressure is required. Therefore, for the adjustment of the wrinkle, the wrinkle can be reduced by appropriately reducing the pressure setting for the long specification, and the pressure is increased for the short specification to prevent the deviation;
6 Different thickness films have different degrees of wrinkling, thick film stiffness is better, less wrinkles, thin film is more open, so the thin film should be adjusted to increase the strength of the parameters to overcome For the generation of wrinkles, different thickness of the film should have different special data for slitting;
7 The product that is slit inside and outside the slitting machine may have different degrees of wrinkling due to the different angles (wrap angles) entering the winding roller. The difference between the inner and outer wrinkles of each slitting machine should be compared, such as The difference is obvious. During the slitting process, the specification that is prone to wrinkle should be cut on the side that is not prone to wrinkle;
8 The wrinkle reduction can also be achieved by adjusting the venting performance of the pressure roller and improving the stability of the winding arm.

Super Clear Tape Slitting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

Seven. Sharp edge
The curling occurs at the edge of the film winding, which causes the curling. The reason is that the edge of the thick film is curled up and the edge part is lifted up; the second is that the winding is too tight, and the tension can be shortened by slitting. Speed ??to improve the resulting edge curling phenomenon; third, the cutter is too blunt, and the stretching phenomenon occurs at the slit when slitting, causing the edge of the film roll to be turned outwards after winding to cause the curling edge, and the cutting should be replaced in time. The knife can avoid the occurrence of the curling problem; the fourth is that the tool is not installed correctly, such as the blade is close to the edge of the sipe and the blade is passivated. Cutting with a round knife can improve the curling of the film roll.
In the use of the unwinding process, there will be different degrees of side-floating in the unwinding process, and it is impossible to track the alignment with the electric eye, which directly affects the use effect. Therefore, it is necessary to change the product with the curled edge.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com