1300mm Tape Cutting Machine

1300mm Tape Cutting Machine

Tension information detection method
(1) Tension sensor detection method: It is a method of detecting the tension directly, closely combined with the machine, and without moving parts. Usually two sensors are paired and mounted on the end shafts on both sides of the detection guide roller.
(2) Roll diameter calculation type detection method: It uses the proximity switch installed at the reel to detect the rotation speed of the reel. Because the reel rotates once, the winding diameter will change twice the thickness of the material.
The current diameter of the reel is obtained by cumulative calculation by the initial value of the reel diameter and the material thickness, and the change of the corresponding reel diameter reflects the change of the actual tension value.
(3) Floating roller position detection mode: It uses the cylinder attached to the slitter to connect the floating roller to drive the angular displacement sensor to detect the tension change. When the tension is stable, the tension on the material is balanced with the cylinder force, so that the floating roller is in the center position. When the tension changes, the balance between the tension and the cylinder force is broken, and the position of the floating roller will rise or fall. At this time, the swing lever will rotate around a point and drive the floating roller angular displacement sensor to rotate together.
(4) Floating roller position + tension sensor combined tension detection mode: It can simultaneously detect the floating roller position signal output by the floating roller angular displacement sensor and the tension signal output by the tension sensor, thereby providing higher precision tension control to the system. [3].

1300mm Tape Cutting Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)

2. Interface identifier
Due to the large thickness of the film interface, the film roll for some applications must be properly handled at the interface to avoid unnecessary problems, such as slowing down, increasing the gap between the coating blade, and printing the offset plate. The interface products must be identified as necessary to facilitate customer identification and internal management.
1 The color of the adhesive interface is generally beige, special requirements are used according to the regulations. For example, Shanghai Ziquan requires the use of black adhesive tape; the marking method of the joint position is operated according to the regulations, such as Zhuhai Zhongfu Pearl Film, Shenzhen Ruimei The hot film is required to be marked at the ends of the interface with yellow paper dust protruding from the end of the film roll by about 1 cm; other special marks are operated according to the requirements of the production tribe.
2 Require the slitting workshop to mark the length number of the joint product without special requirements after the length of the label in the length column of the package label, and mark the “buter” mark on the note bar of the computer, and mark “+” on the remark column. Marking, pearl film and imitation paper film and exporting pearl film should indicate the length of each product before and after the joint on the length column of the product specification. For special requirements, the relevant marking work should be done according to the regulations (such as Shanghai Ziquan product port). The rate of less than or greater than 25% requires the number of interface products on each board product).

1300mm Tape Cutting Machine

The basic knowledge of the slitting machine and its development process --

Basic knowledge and development of slitting machine
       In the modern packaging industry, the slitting machine is a relatively important equipment that is often used before and after printing. The raw materials are mainly cut before printing, such as paper, plastic film and so on. This is a process that raw material manufacturers must complete in order to meet the width requirements of packaging manufacturers such as customers. The slitting machine is used to divide the printing and composite film of a plurality of sets of patterns of a fixed width into a finished film roll to adapt to the subsequent automatic packaging and bag making process.
       With the improvement of flexible packaging automation and consumer goods manufacturers focusing on reducing the inefficiency and pollution of intermediate links, some manufacturers have gradually changed the process and replaced manual packaging with more automated automatic packaging lines. As the demand for coils continues to increase, the position of the slitter is becoming more and more important, and higher requirements are placed on the efficiency of the slitter.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com