Slitting Machine Metal Coil

Slitting Machine Metal Coil

Slitting machine instruction manual -

Second, the use of procedures;
1. Check whether the parts of the machine are loose due to transportation and other reasons, adjust the four foot screws of the machine, and verify that the machine is level on the ground.
2. External high-pressure gas is supplied to the pressure regulating valve. The purpose of the second air pipe blowing is to eliminate the residual nozzle in the empty groove at the lower right of the drum, so that the drum can smoothly accept the new nozzle and adjust the pressure of the pressure regulating valve. The best use.

Slitting Machine Metal Coil

Causes, countermeasures and effects on the quality of BOPP film slitting quality ---

One. Winding too loose / too tight
     Among the many factors affecting the quality of product use, the tightness of the film roll is critical, and the tightness control is moderate, which not only ensures the quality of the slitting, but also compensates for the quality defects caused by the film making process, but the tightness of the winding. Improper control will inevitably directly affect the quality of the product. As a metaphor, if we compare the film formation to the process of producing rice, the cutting is the cook of the rice. The quality of the rice is important, but the cooking time can not be sloppy, in the various control indicators of the cutting. The grasp of the tightness of the winding is like grasping the amount of rice water used in the cooking process. The lack of water and water must have a direct impact on the quality of the rice.

(1) Several methods for judging the tightness of winding
1. Acupressure test method: the examiner presses the surface or end face of the film roll by hand to judge
Whether the volume tightness is suitable. This is a commonly used test method. The advantages are fast, intuitive, and highly reliable, but it requires some experience, lack of data support, and difficulty in recording. 2. Hardness measurement method: The hardness is measured by using a durometer, and the data is spoken.
The advantages are scientific, quantitative, convenient recording, and less disputes on judgment differences. The disadvantage is that only the surface of the film roll can be detected, and the facts inside the film roll cannot be reflected.
3. Visual analysis method: judging the film roll by visually changing the color change of the end face of the film roll or the shape of the end face
For the same product, the darker the end face, the tighter the winding, especially at the near paper tube. The tightness of the winding is often black; for the end shape, the star is the best. According to the judgment, the appearance of a single star may be the phenomenon of tightness of the film, and the occurrence of double stars should be caused by the tightness of the film. The advantages of visual methods are fast and accurate, but they can only analyze some individual winding problems, which is not comprehensive enough.
4. Process tapping method: tapping the membrane surface with a rigid object during the slitting and winding process, through the feel
And the sound to judge the tightness of the film roll, this method can track the film winding tightness from the inside to the outside, the accuracy and credibility are higher, but it will damage the film surface and have certain operation. Dangerousness, we have forbidden to use this method to test the tightness of film roll since 2000. This method is currently only suitable for non-conventional occasions such as product development, slitting control analysis.
Although the current tapping method is not allowed, we use a combination of acupressure test, hardness measurement and visual analysis in the daily slitting process. There is sufficient means to accurately determine the tightness of the winding. Judge. Since the hardness test method is less used in the film industry, the time for using this method is also short. The test method is introduced below.

Slitting Machine Metal Coil

Reasons, countermeasures and effects of BOPP film slitting quality ---

four. Deviation
Deviation refers to the phenomenon that part of the film on the end face of the film roll is misaligned, which is caused by the sliding of the film during the winding process.

2. Causes and countermeasures of deviation:
(1) The problem of the quality of the slitting in the same category as the deviation of the end face is, in terms of degree, the degree of misalignment is more serious than the misalignment of the end face; in terms of nature, the general end face is not a continuous problem. However, the deviation is mostly an accidental problem; from the analysis of the reasons, the cause of the unevenness of the end face may cause the occurrence of the deviation problem.
(2) Since the deviation of the deviation from the end face is more prominent, the eye point should be placed in the fine point when the end face is not aligned. When analyzing the deviation problem, the eye point should be widened, especially the factor of the cutting speed. The effect is that the acceleration and deceleration are too rapid. For a film with good smoothness, it is easy to cause slippage and cause a split layer, and the slitting speed should be slowed down.
(3) For products with narrow slitting, too tight winding of the film roll will cause the film to slip laterally. If the film roll is too loose, air will be trapped, which will cause the film roll end to be staggered. Roll tension.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com