Slitting machine instruction manual -
Second, the use of procedures;
3. Connect the external three-phase power supply, open the key switch placed on the operation button box, the green light on the right indicates that the power supply has been normally turned on, and the black knob adjuster placed on the corner box of the operation button is the small puller in the upper right corner of the control wheel drum. The speed of the motor is adjusted to the speed of the small puller by turning the knob. In actual use, the knob is adjusted to the highest (clockwise direction).
Causes, countermeasures and effects on the quality of BOPP film slitting quality ---
(2) The purpose, method and characteristics of hardness testing
1. OBJECTIVE: The hardness test method provides a quantifiable means for determining the tightness of the film roll and provides a quantifiable basis for the determination.
Some of the product quality characteristics can be quantitative, and some can not be quantified, can only be qualitative. In the past, our judgment on the tightness of the film winding is only based on the hand feeling. The scale of the judgment is difficult to grasp, and the difference between different inspectors Larger. In actual work, when measuring, the non-quantitative characteristics are usually converted into quantifiable substitute quality characteristics, which are used as the basis for evaluation, inspection and assessment. Film roll hardness testing is a means of quantitative control of the main quality characteristics of the slitting under this guiding ideology. However, it is worth emphasizing that not all quality characteristics must be quantified, especially the film as a process material quality characteristic, there are quantitative measurement characteristics, such as thickness, tensile strength, gloss, etc., also have qualitative characteristics, only the process Subjective judgments such as wrinkles, blots, chromatic aberrations, etc.
2. Several characteristics of film roll hardness
1 Different film varieties, the hand tightness is similar but the hardness data is different. This is because the hand roll is used to squeeze the film roll in a certain area of ??the finger, which is a test of one surface, and when the hardness tester is used, it is a The pin point is pressed against the film roll, which is a detection of a point, and there will be differences between the two;
2 different film varieties have different winding hardness requirements, which are based on the characteristics and uses of various films;
3 The tightness and hardness of the film roll are not completely linear. The most sensitive value is between 87 and 95. When the hardness is as low as 85, the rewinding does not affect the hardness. Similarly, when the hardness is high. At 97 o'clock, the effect of rewinding on the film roll hardness is getting smaller and smaller.
4 Winding hardness is a reference index for quantifying the winding tightness. It only reflects a quality characteristic of the film roll surface and does not reflect the fullness of the film roll. Therefore, the key is to effectively control the film roll tightness. The quality of the product used.
Reasons, countermeasures and effects of BOPP film slitting quality ---
ten. Color circle
The color circle is caused by a certain degree of contamination inside or outside the film, which causes the quality of the color circle on the end face of the film roll after slitting and winding. Membrane surface pollution sources come from two aspects. One is the film-forming process. The color circles generated in the front part of the film, such as raw materials, feeding systems, extrusion systems, and die flow channels, generally cause pollution to the inside of the film (core layer). Some color-circle products can clearly observe a large amount of fish-eye impurities in the film. The color circles generated in the film-forming stage and the slitting process mainly cause pollution to the outside (surface) of the film, but whether it is internal or external pollution, It is impossible to remove the impurities from the contaminated film and restore the original appearance. The product with serious color circle has low transparency, the film color is different from the normal product, and it can not be used at all. It can only be reduced to other external treatments, while the products with slight color circles are It has little effect on the transparency of the product and does not affect the use effect of the single film. However, due to the inconspicuous appearance of the color circle product, the “selling phase” is poor, which has a great influence on the image of the German brand. It is not suitable for direct delivery. Secondary processing. If the color circle is caused by external dust pollution factors, the dust will be adsorbed on the surface of the film, resulting in poor quality of heat sealing and poor laser compression.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc