Adhesive Tape Slitting Machine Rewind Tape Machine

Adhesive Tape Slitting Machine Rewind Tape Machine

Slitting machine instruction manual -

Second, the use of procedures;

3. Connect the external three-phase power supply, open the key switch placed on the operation button box, the green light on the right indicates that the power supply has been normally turned on, and the black knob adjuster placed on the corner box of the operation button is the small puller in the upper right corner of the control wheel drum. The speed of the motor is adjusted to the speed of the small puller by turning the knob. In actual use, the knob is adjusted to the highest (clockwise direction).

Adhesive Tape Slitting Machine Rewind Tape Machine

Reasons, countermeasures and effects of BOPP film slitting quality ---

twelve. Interface quality problem (poor interface quality, interface identifier does not match)
1. Interface requirements
Due to poor interface, the quality of the film roll may be broken or wrinkled, which may cause adverse effects in the user's use. Therefore, the film interface must be connected to the specified specification to ensure the joint quality of the interface. Specific requirements are as follows: 
1 The two sections of the joint are cut and flattened horizontally, and the beige (or other specified color) adhesive tape with a width of 72 mm is firmly adhered to the front and back sides of the film;
2 In order to improve the interface quality, the film interface is required to be straight and balanced with the paper tube direction, and the interface is required to be flush and wavy. The interfaces at both ends are in the middle of the tape. Try to avoid the size of the edge. The adhesive tape is attached to the film. No obvious bubbles;
3 The film surface at the interface is required to be smooth without obvious wrinkling;
4 Do the identification of the joint position as specified.

Adhesive Tape Slitting Machine Rewind Tape Machine

Domestic cutting machine development status and outlets ---

First, the status quo of domestic slitting machine
At present, the domestic use of the slitting machine is mainly divided into several stages, and the first stage is mainly used for the main line slitting as one slitting. One slitting is mainly provided to downstream deep processing enterprises, and the downstream customers are divided into secondary slitting or three slitting. The film making manufacturers of this meeting are mainly cut into one slitting, with the competition of film forming enterprises in recent years. Intense, in order to provide better services to downstream customers, film companies have also added a second cut. In one slitting, the most used brand is CommScope, followed by Atlas, and the Japanese slitter is rarely used in one slitting. With the rise of domestic equipment manufacturing industry in recent years, domestic slitting machines have a certain foothold in a slitting process. Of course, compared with foreign slitting machines, there is still a certain gap in domestic slitting machines. From the user's point of view, I personally think that there is a certain misunderstanding, mainly because of the lack of deep understanding of the slitter market. Everyone knows that there must be a performance price ratio when purchasing a piece of equipment. In fact, the performance and price ratio of the above mentioned brands are not necessarily the best. Some people in the United States have done such an experiment. The above-mentioned brand slitting machine is compared with the Japanese Knife cutting machine. When the same film material is cut, the result is that Japan's Kataoka wins, mainly in terms of stability and speed, speed reduction and non-stretching. Japan's Kataoka has shown superior quality and its price is lower than the above brands. Unfortunately, in the domestic film-making enterprises, no one slitting machine used Japan's Kataoka slitting machine. It is a pity that domestic companies have bought foreign second-rate equipment at the highest price. I have researched the US market. Japan's Kataoka has a high market share in the US market. I believe that with the increase in market demand and fierce competition, domestic companies will come out of this misunderstanding and re-recognize the market of slitting machines. Compared with the first slitting, the third slitting and the one slitting, the status quo of the domestic slitting machine is diversified. One slitting is mainly the importing equipment to play the leading role, while the secondary slitting and three slitting fields are in the field. The domestic market has its own magical powers, including Europe, Japan, and Taiwan. In recent years, the domestically produced slitting machines have gradually replaced the trend of foreign brands, resulting in the following results:
1. Foreign advanced cutting technology has gradually flowed to China;
2. The rise of domestic manufacturing;
3. Popularization of advanced control technology;
4, the low cost of manufacturing causes the price of the slitting machine to be low;
The above various reasons have jointly promoted the domestic film-making enterprises to choose domestic slitting machines. As time goes by, I believe that the domestic cutting opportunities become more mature and the performance is better.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com